AC050000B2209J6BCS Datasheet AC01000001000JACCS, AC01000008208JACCS, AC03000006809JACCS | P7-P9

AC01-CS, AC03-CS, AC05-CS

www.vishay.com

Vishay Draloric

Revision: 12-Jul-16

Document Number: 28909

For technical questions, contact: ww1resistors@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

TESTS PROCEDURES AND REQUIREMENTS

All tests are carried out in accordance with the following

specifications:

• IEC 60115-1, generic specification (includes tests)

The test and requirements table contains only the most

important tests. For the full test schedule refer to the

documents above.

The tests are carried out in accordance with IEC 60068-2-xx

test method and under standard atmospheric conditions in

accordance with IEC 60068-1, 5.3.

Climatic category -40 / 200 / 56 (rated temperature range:

lower category temperature, upper category temperature;

damp heat, steady state, test duration: 56 days) is valid.

Unless otherwise specified the following values apply:

• Temperature: 15 °C to 35 °C

• Relative humidity: 45 % to 75 %

• Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar)

For performing some of the tests, the components are

mounted on a test board in accordance with IEC 60115-1,

4.31.

In test table below, only the relevant and commonly referred

tests and related clauses of IEC 60115-1 and

IEC 60068-2-xx test methods are mentioned.

TEST PROCEDURES AND REQUIREMENTS

IEC 60115-1

CLAUSE

IEC 60068-2

TEST

METHOD

TEST PROCEDURE

REQUIREMENTS

PERMISSIBLE CHANGE (R

MAX.

)

4.13 - Short time overload

Room temperature;

10x rated power P

;

5 s

± (2 % R + 0.1 )

4.16

21 (Ua

)

21 (Ub)

21 (Uc)

Robustness of

terminations

Tensile, bending and torsion

No damage

± (0.5 % R + 0.05)

4.18 20 (Tb)

Resistance to

soldering heat

Unmounted components

(260 ± 5) °C; (10 ± 1) s

± (0.5 % R + 0.05)

4.23 Climatic sequence:

4.23.2 2 (Ba) Dry heat 16 h; 200 °C

± (1 % R + 0.05 )

4.23.3 30 (Db)

Damp heat

(accelerated)

1st cycle

24 h; 55 °C;

90 % to 100 % RH

4.23.4 1 (Aa) Cold 2 h; -55 °C

4.23.5 13 (M) Low air pressure

2 h; 8.5 kPa;

15 °C to 35 °C

4.23.6 30 (Db)

Damp heat

remaining cyclic

5 days; 55 °C;

95 % to 100 % RH; 5 cycles

4.24 78 (Cab)

Damp heat,

(steady state)

56 days; (40 ± 2) °C;

(93 ± 5) % RH

± (5 % R + 0.1 )

4.25.2 -

Endurance

(at room temperature)

1000 h;

loaded with 116 % of P

;

1.5 h ON and 0.5 h OFF

± (5 % R + 0.1 )

4.25.3 -

Endurance

(at 200 °C)

1000 h; without load ± (5 % R + 0.1 )

1.2 / 50 μs surge test as

defined in IEC 61000-4-5

(up to 6 kV)

Internal impedance of surge

tester is 2 ;

10 pulses at 30 s interval

± (5 % R + 0.1 )

Fail safe mains fusing

at 230 V

Resistance > 100 k, fusing time < 2 s

(fusing without flame and explosion)

AC01-CS, AC03-CS, AC05-CS

www.vishay.com

Vishay Draloric

Revision: 12-Jul-16

Document Number: 28909

For technical questions, contact: ww1resistors@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

DIMENSIONS

Notes

(1)

For AC01-CS, dimension given is applicable for 10R to 100R; for lower ohmic values < 10R, D

max.

might reach 5.5 mm.

(2)

For AC05-CS, L = L

; there is no lacquer on termination lead.

DIMENSIONS - Leaded resistor types, mass and relevant physical dimensions

MODEL L

max.

1 max.

max.

nom.

BMASS

AC01-CS

(1)

11.0 mm 13.0 mm 5.0 mm 0.7 mm 63 mm 0.52 g

AC03-CS 13.0 mm 19.0 mm 6.0 mm 0.8 mm 63 mm 0.78 g

AC05-CS

(2)

17.0 mm 17.0 mm 10.0 mm 0.8 mm

83 mm 2.25 g

93 mm 2.5 g

AC01-CS and AC03-CS AC05-CS

Legal Disclaimer Notice

www.vishay.com

Vishay

Revision: 08-Feb-17

Document Number: 91000

Disclaimer



ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE

RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,

“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other

disclosure relating to any product.

Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or

the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all

liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,

consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular

purpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of

typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding

statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a

particular product with the properties described in the product specification is suitable for use in a particular application.

Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over

time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s

technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,

including but not limited to the warranty expressed therein.

Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining

applications or for any other application in which the failure of the Vishay product could result in personal injury or death.

Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.

Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for

such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document

or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.

P1-P3 P4-P6 P7-P9

AC050000B2209J6BCS

Mfr. #:

Buy AC050000B2209J6BCS

Manufacturer:

Vishay

Description:

Wirewound Resistors - Through Hole 5watt 22ohm 5% Safety Resisto

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

AC050000B2209J6BCS

AC050000B2209J6BCS

Products related to this Datasheet