Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
Surface Mount
NPCAP
TM
-PXASeries
・
Super low ESR, impedance and high heat resistance have been obtained by using
conductive polymer as electrolyte
・
Rated voltage range : 2.5 to 25V
dc
, case size range :
φ
5×5.7L to
φ
10×12.2L
・
Suitable for DC-DC converters, voltage regulators and decoupling applications used on
computer motherboards etc.
・
Solvent resistant type (see PRECAUTIONS AND GUIDELINES)
・
RoHS2 Compliant
・
Halogen Free
◆
SPECIFICATIONS
Items Characteristics
Category
Temperature Range
-55 to +105
℃
Rated Voltage Range
2.5 to 25V
dc
Capacitance Tolerance
±
20% (M) (at 20
℃
, 120Hz)
Surge Voltage
Rated voltage
×
1.15 (Rated voltage 2.5 to 20V
dc
, 25V
dc
) / Rated voltage
×
1.00 (Rated voltage 23V
dc
) (at 105
℃
)
Leakage Current
Shall not exceed values shown in STANDARD RATINGS. (at 20
℃
after 2 minutes)
Dissipation Factor
(tan
δ
)
0.12 max.
(at 20
℃
, 120Hz)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Z(-25
℃
)/Z(+20
℃
)
≦
1.15
Z(-55
℃
)/Z(+20
℃
)
≦
1.25
(at 100kHz)
Endurance
The following specifications shall be satisfied when the capacitors are restored to 20
℃
after the rated voltage is applied for 15,000 hours
(F45 : 3,000 hours) at 105
℃
.
Appearance No significant damage
Capacitance change
≦±
20% of the initial value
D.F. (tan
δ
)
≦
150% of the initial specified value
ESR
≦
150% of the initial specified value
Leakage current
≦
The initial specified value
Bias Humidity
The following specifications shall be satisfied when the capacitors are restored to 20
℃
after subjecting them to the DC rated voltage at
60
℃
, 90 to 95% RH for 1,000 hours(F45 : 500 hours).
Appearance No significant damage
Capacitance change
≦±
20% of the initial value
D.F. (tan
δ
)
≦
150% of the initial specified value
ESR
≦
150% of the initial specified value
Leakage current
≦
The initial specified value
Surge Voltage
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105
℃
for 30 seconds
through a protective resistor(R=1k
Ω
) and discharge for 5 minutes 30 seconds.
Appearance No significant damage
Capacitance change
≦±
20% of the initial value
D.F. (tan
δ
)
≦
150% of the initial specified value
ESR
≦
150% of the initial specified value
Leakage current
≦
The initial specified value
Failure Rate
0.5% per 1,000 hours maximum (Confidence level 60% at 105
℃
)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.
◆
DIMENSIONS [mm]
0.3max.
A
±
0.2
W
P
Note : L+0.1/-0.2 for F45
L
±
0.5 for HC0 and JC0
Terminal Code : A
φ
D
±
0.5
B
±
0.2
C±
0.2
L
±
0.3 (Note)
Size code
E60
F45
F60
H70
HC0
J80
JC0
φ
D
5
6.3
6.3
8
8
10
10
L
5.7
4.4
5.7
6.7
12.0
7.7
12.2
A
5.3
6.6
6.6
8.3
8.3
10.3
10.3
B
5.3
6.6
6.6
8.3
8.3
10.3
10.3
C
5.9
7.2
7.2
9.0
9.0
11.0
11.0
W
0.5 to 0.8
0.5 to 0.8
0.5 to 0.8
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
P
1.4
1.9
1.9
3.1
3.1
4.5
4.5
◆
PART NUMBERING SYSTEM
Supplement code
Size code
Capacitance tolerance code
Taping code
Terminal code
Series code
Category
A P X A A R A GM
1 3 42 6 7 8 9 10 13125 18171611 1514
Please refer to "Product code guide (conductive polymer type)"
Capacitance code (ex. 10µF:100,100µF:101)
Voltage code (ex. 6.3V:6R3,10V:100)
Lower ESR
PXA
PXE P2-26
◆
MARKING
A
15L
39
16
V
2-28
CAT. No. E1001R
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
