CRY82(TE85L,Q,M) Datasheet CRZ24(TE85L,Q,M), CRZ36(TE85L,Q,M), CRZ20(TE85L,Q,M) | P1-P3

CRY62 to CRZ39

2014-10-09

1

TOSHIBA Zener Diode Silicon Epitaxial Type

CRY62 to CRZ39

○ Surge absorber

 Average power dissipation : P = 0.7 W

 Zener voltage : V

Z

= 6.2 to 39 V

 Suitable for compact assembly due to small surface-mount package

“S−FLAT

TM

” (Toshiba package name)

Absolute Maximum Ratings

(Ta = 25

°C

)

Characteristic Symbol Rating Unit

Power dissipation P 0.7 W

Junction temperature T

j

−40 to 150 °C

Storage temperature range T

stg

−40 to 150 °C

Note: Using continuously under heavy loads (e.g. the application of high

temperature/current/voltage and the significant change in

temperature, etc.) may cause this product to decrease in the

reliability significantly even if the operating conditions (i.e.

operating temperature/current/voltage, etc.) are within the

absolute maximum ratings.

Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook

(“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test

report and estimated failure rate, etc).

Land Pattern Dimensions (reference only)

Unit

: mm

JEDEC ―

JEITA ―

TOSHIBA 3-2A1S

Weight: 0.013 g (typ.)

2.8

1.2

Unit: mm

Start of commercial production

1999-09

CRY62 to CRZ39

2014-10-09

2

Electrical Characteristics

(Ta = 25°C

)

Product

No.

Zener Voltage

Zener

Impedance

Temperature

Coefficient

of Zener

Voltage

α

T

(mV / °C)

Forward

Voltage

Reverse

Current

V

Z

(V)

Measure-

ment

Current

I

Z

(mA)

r

d

(Ω)

Measure-

ment

Current

I

Z

(mA)

V

F

(V)

Measure

-ment

Current

I

F

(A)

I

R

(μA)

Measure-

ment

Voltage

V

R

(V)

Min

Typ. Max Max Typ. Max Max Max

CRY62 5.6 6.2 6.8 10 60 10 2 3 1.0 0.2 10 3.0

CRY68 6.2 6.8 7.4 10 60 10 3 4 1.0 0.2 10 3.0

CRY82 7.4 8.2 9.0 10 30 10 4 6 1.0 0.2 10 4.9

CRZ10 9.0 10.0 11.0 10 30 10 6 9 1.0 0.2 10 6.0

CRZ12 10.8 12.0 13.2 10 30 10 8 13 1.0 0.2 10 8.0

CRZ13 11.7 13.0 14.3 10 30 10 9 14 1.0 0.2 10 9.0

CRZ15 13.5 15.0 16.5 10 30 10 11 17 1.0 0.2 10 10.0

CRZ16 14.4 16.0 17.6 10 30 10 12 19 1.0 0.2 10 11.0

CRZ18 16.2 18.0 19.8 10 30 10 14 23 1.0 0.2 10 13.0

CRZ20 18.0 20.0 22.0 10 30 10 16 26 1.0 0.2 10 14.0

CRZ24 21.6 24.0 26.4 10 30 10 20 32 1.0 0.2 10 17.0

CRZ27 24.3 27.0 29.7 10 30 10 23 36 1.0 0.2 10 19.0

CRZ30 27.0 30.0 33.0 10 30 10 25 40 1.0 0.2 10 21.0

CRZ33 29.7 33.0 36.3 10 30 10 26 41 1.0 0.2 10 26.4

CRZ36 32.4 36.0 39.6 9 30 9 28 45 1.0 0.2 10 28.8

CRZ39 35.1 39.0 42.9 8 35 8 30 48 1.0 0.2 10 31.2

CRY62 to CRZ39

2014-10-09

3

Marking

Abbreviation Code Part No.

6

.

2 CRY62

6

.

8 CRY68

8

.

2 CRY82

10 CRZ10

12 CRZ12

13 CRZ13

15 CRZ15

16 CRZ16

18 CRZ18

20 CRZ20

24 CRZ24

27 CRZ27

30 CRZ30

33 CRZ33

36 CRZ36

39 CRZ39

Handling Precaution

The absolute maximum ratings denote the absolute maximum ratings, which are rated values and must not be

exceeded during operation, even for an instant. The following are the general derating methods that we recommend

when you design a circuit with a device.

P: We recommend that the worst case power dissipation be no greater than 50% of the absolute

maximum rating of power dissipation. Carry out adequate heat design.

P

RSM

: We recommend that a device be used within the recommended area in the figure, P

RSM

-tw.

T

j

: Derate this rating when using a device in order to ensure high reliability. We recommend that the

device be used at a T

j

of below 120°C.

Thermal resistance between junction and ambient fluctuates depending on the device’s mounting condition. When

using a device, design a circuit board and a soldering land size to match the appropriate thermal resistance value.

Please refer to the Rectifiers databook for further information.

Part No.

(or abbreviation code)

Cathode mark and Lot code

CRY82(TE85L,Q,M)

CRY82(TE85L,Q,M)

Products related to this Datasheet