OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

LQG15HS47NJ02D

P1-P3P4-P6P7-P9P10-P11
Spec No. JELF243B-0010P-01 P.4/11
MURATA MFG.CO., LTD
Reference Only
6. Electrical Performance
No. Item Specification Test Method
6.1
Inductance Inductance shall meet item 3. Measuring Equipment:
Agilent 4291A or equivalent
Measuring Frequency: 100MHz
Measuring Condition:
Test signal level/ about 7dBm
Electrical length/ 0.94cm
Weight/ about 1N to 5N
Measuring Fixture: Agilent 16193A
Position coil under test as shown in below and
contact coil with each terminal by adding weight.
Polarity marking should be a topside,and polarity
marking should be in the direction of the fixture
for position of chip coil.
Measuring Method: See P.11
[Electrical Performance:Measuring Method of
Inductance/ Q]
6.2 Q Q shall meet item 3.
6.3 DC Resistance DC Resistance shall meet item 3. Measuring Equipment: Digital multi meter
6.4 Self Resonant
Frequency (S.R.F)
S.R.F shall meet item 3. Measuring Equipment:
Agilent 8753C or equivalent
6.5 Rated Current Self temperature rise shall be
limited to 25°C max.
The rated current is applied.
7. Mechanical Performance
No. Item Specification Test Method
7.1 Shear Test Chip coil shall not be damaged
after tested as test method.
Substrate: Glass-epoxy substrate
(in mm)
Force: 5N
Hold Duration: 5s±1s
Applied Direction: Parallel to PCB
7.2 Bending Test Chip coil shall not be damaged
after tested as test method.
Substrate: Glass-epoxy substrate
(100mm×40mm×0.8mm)
Speed of Applying Force: 1mm / s
Deflection: 2mm
Hold Duration: 30s
(in mm)
Polarity Marking
0.5mm
11.5mm
45
R340
F
Deflection
45
Product
Pressure jig
Land
0.4 0.55
0.55
0.5
F
Chip Coil
Substrate
Spec No. JELF243B-0010P-01 P.5/11
MURATA MFG.CO., LTD
Reference Only
No. Item Specification Test Method
7.3 Vibration Appearance: No damage
Inductance Change: within ±10%
Oscillation Frequency:
10Hz to 55Hz to 10Hz for 1 min
Total Amplitude: 1.5mm
Testing Time: A period of 2 hours in each of
3 mutually perpendicular directions.
7.4 Solderability The wetting area of the electrode
shall be at least 90% covered with
new solder coating.
Flux: Ethanol solution of rosin 25(wt)%
(Immersed for 5s to 10s)
Solder: Sn-3.0Ag-0.5Cu
Pre-Heating: 150°C±10°C / 60s to 90s
Solder Temperature: 240°C±5°C
Immersion Time: 3s±1s
7.5 Resistance to
Soldering Heat
Appearance: No damage
Inductance Chang
e: within ±10%
Flux: Ethanol solution of rosin 25(wt)%
(Immersed for 5s to 10s)
Solder: Sn-3.0Ag-0.5Cu
Pre-Heating: 150°C±10°C / 1 min to 2 min
Solder Temperature: 270°C±5°C
Immersion Time: 10s±1s
Then measured after exposure in the room
condition for 24h±2h.
8. Environmental Performance
It shall be soldered on the substrate.
No. Item Specification Test Method
8.1 Humidity Appearance: No damage
Inductance Change: within ±10%
Temperature: 40°C±2°C
Humidity: 90%(RH) to 95%(RH)
Time: 1000h (+48h,-0h)
Then measured after exposure in the room
condition for 24h±2h.
8.2 Heat Life Temperature: 125°C±2°C
Current: Rated Current (See the 3.)
Time: 1000h (+48h, -0h)
Then measured after exposure in the room
condition for 24h±2h.
8.3 Humidity Load Temperature: 40°C±2°C
Humidity: 90%(RH) to 95%(RH)
Current: Rated Current (See the 3.)
Time: 1000h (+48h, -0h)
Then measured after exposure in the room
condition for 24h±2h.
8.4 Temperature
Cycle
1 cycle:
1 step: -55°C (+0°C, -3°C) / 30 min±3 min
2 step: Ordinary temp. / 2 min to 3 min
3 step: +125°C (+3°C, -0°C) / 30 min±3 min
4 step: Ordinary temp. / 2 min to 3 min
Total of 10 cycles
Then measured after exposure in the room
condition for 24h±2h.
9. Specification of Packaging
9.1 Appearance and Dimensions of paper tape (8mm-wide)
(in mm)
0.62±0.04
1.12±0.04
2.0±0.05
2.0±0.05
4.0±0.1
φ
1.5±
3.5±0.05
8.0±0.2
0.8max.
0.1
0
Direction of feed
Polarity marking
1.75±0.1
Spec No. JELF243B-0010P-01 P.6/11
MURATA MFG.CO., LTD
Reference Only
9.2 Specification of Taping
(1) Packing quantity (standard quantity)
10,000 pcs. / reel
(2) Packing Method
Products shall be packed in the cavity of the base tape and sealed by top tape and bottom tape.
(3) Sprocket hole
The sprocket holes are to the right as the tape is pulled toward the user.
(4) Spliced point
Base tape and Top tape has no spliced point.
(5) Missing components number
Missing components number within 0.1 % of the number per reel or 1 pc., whichever is greater,
and are not continuous. The Specified quantity per reel is kept.
9.3 Pull Strength
Top tape
5N min.
Bottom tape
9.4 Peeling off force of cover tape
Speed of Peeling off 300mm / min
Peeling off force 0.1N to 0.6N
(minimum value is typical)
9.5 Dimensions of Leader-tape, Trailer and Reel
There shall be leader-tape ( top tape and empty tape) and trailer-tape (empty tape) as follows.
(in mm)
9.6 Marking for reel
Customer part number, MURATA part number, Inspection number (1), RoHS marking (2),
Quantity etc ･･･
1) <Expression of Inspection No.>
□□ OOOO 
(1) (2) (3)
(1) Factory Code
(2) Date First digit : Year / Last digit of year
Second digit : Month / Jan. to Sep. 1 to 9, Oct. to Dec. O, N, D
Third, Fourth digit : Day
(3) Serial No.
2) <Expression of RoHS marking > ROHS – Y (△)
(1) (2)
(1)
RoHS regulation conformity parts.
(2) MURATA classification number
9.7 Marking for Outside package (corrugated paper box)
Customer name, Purchasing order number, Customer part number, MURATA part number,
RoHS marking (2), Quantity, etc ･･･
F
165 to 180 degree
Top tape
Bottom tape
Base tape
Empty tape
190 min.
Leader
Trailer
2.0±0.5
13.0±0.2
21.0±0.8
180
60
9.0
13.0±1.4
+1
-
0
+0
-3
Direction of feed
210 min.
160 min.
Top tape
+1
-0
Label
P1-P3P4-P6P7-P9P10-P11

LQG15HS47NJ02D

Mfr. #:
Buy LQG15HS47NJ02D
Manufacturer:
Murata Electronics
Description:
Fixed Inductors 47nH 5% Hi-Freq
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet