LH1532AAC, LH1532AACTR, LH1532AB
www.vishay.com
Vishay Semiconductors
Rev. 1.6, 25-Jul-11
2
Document Number: 83829
For technical questions, contact: optocoupleranswers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Notes
• Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not
implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute
maximum ratings for extended periods of the time can adversely affect reliability.
(1)
Refer to current limit performance application note for a discussion on relay operation during transient currents.
(2)
Refer to reflow profile for soldering conditions for surface mounted devices (SMD). Refer to wave profile for soldering conditions for through
hole devices (DIP).
(3)
Breakdown occurs between the output pins external to the package.
Note
• Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering
evaluations. Typical values are for information only and are not part of the testing requirements.
ABSOLUTE MAXIMUM RATINGS (T
amb
= 25 °C, unless otherwise specified)
PARAMETER TEST CONDITION SYMBOL VALUE UNIT
INPUT
LED continuous forward current I
F
50 mA
LED reverse voltage I
R
10 μA V
R
8V
OUTPUT
DC or peak AC load voltage I
L
50 μA V
L
350 V
Continuous DC load current, one pole operating I
L
120 mA
Continuous DC load current, two poles
operating
I
L
110 mA
Peak load current (single shot) t = 100 ms I
P
(1)
SSR
Ambient temperature range T
amb
- 40 to + 85 °C
Storage temperature range T
stg
- 40 to + 150 °C
Pin soldering temperature
(2)
t = 10 s max. T
sld
260 °C
Input to output isolation test voltage t = 1 s V
ISO
5300 V
RMS
Pole-to-pole isolation voltage (S1 to S2),
(3)
(dry air, dust free, at sea level)
1600 V
Output power dissipation (continuous) P
diss
600 mW
ELECTRICAL CHARACTERISTICS (T
amb
= 25 °C, unless otherwise specified)
PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT
INPUT
LED forward current, switch turn-on I
L
= 100 mA, t = 10 ms I
Fon
12mA
LED forward current, switch turn-off V
L
= ± 300 V I
Foff
0.2 0.9 mA
LED forward voltage I
F
= 10 mA V
F
1.15 1.26 1.45 V
OUTPUT
On-resistance I
F
= 5 mA, I
L
= 50 mA R
ON
12 20 25
Off-resistance I
F
= 0 mA, V
L
= ± 100 V R
OFF
0.5 5000 G
Current limit I
F
= 5 mA, t = 5 ms, V
L
= ± 6 V I
LMT
170 210 250 mA
Off-state leakage current
I
F
= 0 mA, V
L
= ± 100 V I
O
0.02 200 nA
I
F
= 0 mA, V
L
= ± 350 V I
O
1μA
Output capacitance
I
F
= 0 mA, V
L
= 1 V C
O
55 pF
I
F
= 0 mA, V
L
= 50 V C
O
10 pF
Pole-to-pole capacitance (S1 to S2) I
F
= 5 mA 0.5 pF
Switch offset I
F
= 5 mA V
OS
0.15 μV
TRANSFER
Capacitance (input to output) V
ISO
= 1 V C
IO
1.1 pF
SWITCHING CHARACTERISTICS (T
amb
= 25 °C, unless otherwise specified)
PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT
Turn-on time I
F
= 5 mA, I
L
= 50 mA t
on
1.4 2.5 ms
Turn-off time I
F
= 5 mA, I
L
= 50 mA t
off
0.7 2.5 ms
