LTC3525L-3
2
3525lfa
V
IN
, V
OUT
Voltage ......................................... –0.3V to 6V
SW Voltage
.................................................. –0.3V to 6V
SW Voltage < 100ns
..................................... –0.3V to 7V
SHDN Voltage
.............................................. –0.3V to 6V
Operating Temperature Range
(Notes 2, 5)
..............................................–40°C to 85°C
Storage Temperature Range
.................. –65°C to 125°C
Lead Temperature (Soldering, 10 sec)
...................300°C
(Note 1)
The
l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at T
A
= 25°C.
V
IN
= 1.2V, V
SHDN
= 1.2V, V
OUT
= 3V unless otherwise noted.
PARAMETER CONDITIONS MIN TYP MAX UNITS
Minimum Input Start-Up Voltage 0.7 0.88 V
Output Voltage (Note 6)
l
2.91 3.00 3.09 V
Quiescent Current, V
OUT
SHDN = V
IN
(Note 4) 7 15 µA
Quiescent Current, V
IN
SHDN = V
IN
(Note 4) 0.5 3 µA
Quiescent Current, V
IN
– Shutdown SHDN = 0V, V
OUT
= 0V
Not Including Switch Leakage
0.1 1 µA
NMOS Switch Leakage Current V
IN
= V
OUT
= V
SW
= 5V, SHDN = 0V 0.1 3 µA
PMOS Switch Leakage Current V
IN
= V
SW
= 5V, V
OUT
= 0V, SHDN = 0V 0.1 6 µA
NMOS Switch On-Resistance (Note 3) 0.5
PMOS Switch On-Resistance (Note 3) 0.85
Peak Current Limit 0.4 0.45 A
SHDN Threshold Voltage 0.3 0.5 0.88 V
SHDN Input Current V
SHDN
= V
IN
or V
OUT
0.01 1 µA
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LTC3525LE-3 is guaranteed to meet performance
specifications from 0°C to 85°C. Specifications over the –40°C to 85°C
operating temperature range are assured by design, characterization and
correlation with statistical process controls.
Note 3: Specification is guaranteed by design and not 100% tested in
production.
Note 4: Current Measurements are performed when the LTC3525L-3 is not
switching.
Note 5: This IC includes overtemperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperature will exceed 125°C when overtemperature protection is active.
Continuous operation above the specified maximum operating junction
temperature may impair device reliability.
Note 6: Consult LTC Marketing for other output voltage options.
PIN CONFIGURATIONABSOLUTE MAXIMUM RATINGS
ORDER INFORMATION
LEAD FREE FINISH TAPE AND REEL PART MARKING PACKAGE DESCRIPTION TEMPERATURE RANGE
LTC3525LESC6-3#PBF LTC3525LESC6-3#TRPBF LCPY 6-Lead Plastic SC70 –40°C to 85°C
Consult LTC Marketing for parts specified with wider operating temperature ranges.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
SHDN 1
GND 2
V
IN
3
6 SW
5 GND
4 V
OUT
TOP VIEW
SC6 PACKAGE
6-LEAD PLASTIC SC70
T
JMAX
= 125°C
θ
JA
= 120°C/W ON BOARD OVER GROUND PLANE
ELECTRICAL CHARACTERISTICS
