MAX. No. of PSUs on 16A
CIRCUIT BREAKER
3 units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230VAC
SPECIFICATION
MODEL
RATED CURRENT
RATED POWER
OUTPUT
SETUP, RISE TIME
HOLD UP TIME (Typ.)
VOLTAGE RANGE
Note.2
FREQUENCY RANGE
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INPUT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
SAFETY STANDARDS
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVER TEMPERATURE
OVER VOLTAGE
16ms/230VAC at full load
1000ms, 80ms / 230VAC at full load
180 ~ 305VAC 254VDC ~ 431VDC
47 ~ 63Hz
1.7 A / 230VAC 1.5A / 277VAC
<0.25mA / 277VAC
-25 ~ +50 (Refer to "Derating Curve")℃
10 ~ 95% RH non-condensing
-40 ~ +70 , 10 ~ 95% RH℃
±0.03%/ (0 ~ 50 )℃℃
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
RIPPLE CURRENT
ENVIRONMENT
SAFETY &
EMC
PROTECTION
440 ~ 470V
Protection type : Shut down and latch off o/p voltage re-power on to recovery
SHORT CIRCUIT
90%
±5%
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃
2. Derating may be needed under low input voltages. Please check the static characteristics for more details.
3. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
4. Refer to warranty statement.
5. Constant current operation region is within 50% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please
reconfirm special electrical requirements for some specific system design.
6. Suitable for indoor use or outdoor use without direct sunlight exposure, please avoid immerse in the water over 30minutes.
7. The unit might not be suitable for lighting applications in EU countries. Please check with your local authorities for the possible use of the unit.
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024 , EAC TP TC 020, light industry level , criteria A
350mA
150.5W
215 ~ 430V
107V ~ 215V
54V ~ 108V
36V ~ 72V 27V ~ 54V
I/P-O/P:3KVAC
I/P-O/P:100M Ohms / 500VDC / 25 / 70% RH℃
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
235 ~ 265V
115 ~ 135V
80 ~ 97V
63 ~ 75V
700mA 1400mA 2100mA 2800mA
150.5W 151.2W 151.2W 151.2W
■ Features :
Constant current design
180~305VAC input only
High efficiency up to 90%
Protections: Short circuit / Over voltage / Over temperature
Cooling by free air convection
Fully encapsulated with IP67 level (Note.6)
Fully isolated plastic case
Class power unit, no FGⅡ
Suitable for LED related fixture or appliance
(such as LED Decoration or Advertisement devices)(Note.7)
100% full load burn-in test
Low cost, high reliability
2 years warranty (Note.4)
150W Single Output LED Power Supply
LPC-150 series
File Name:LPC-150-SPEC 2018-01-10
EMC IMMUNITY
EMC EMISSION
CURRENT ACCURACY ±5.0%
Compliance to EN55032(CISPR32) Class B; EN61000-3-2 Class A(≤80% load); EN61000-3-3, EAC TP TC 020
CONSTANT CURRENT REGION
Note.5
RIPPLE & NOISE
2Vp-p 1Vp-p 1Vp-p 1Vp-p 1Vp-p
479K hrs min. MIL-HDBK-217F (25 )℃
191*63*37.5mm (L*W*H)
0.74Kg; 20pcs/15.8Kg/0.95CUFT
LINE REGULATION
±1%
COLD START 40A(t =750 s measured at 50% I ) at 230VAC
width peakμ
Shut down o/p voltage, recovers automatically after temperature goes down
Hiccup mode, recovers automatically after fault condition is removed
150 ~ 300V
LPC-150-1050
LPC-150-1400
LPC-150-1750
LPC-150-2100
LPC-150-2450
LPC-150-2800
LPC-150-3150
500mA 1050mA 1750mA 2450mA 3150mA
72V ~ 144V
43V ~ 86V
31V ~ 62V 24V ~ 48V
150W 151.2W 150.5W 151.9W 151.2W
1.5Vp-p 1Vp-p 1Vp-p 1Vp-p 1Vp-p
330 ~ 365V
158 ~ 188V
96 ~ 115V
69 ~ 80V
55 ~ 65V
BIS IS15885(for 700mA,1050mA,1400mA,2800mA only), IP67 approved; refer to EN60950-1EAC TP TC 004,
IP67
LPC-150-350
LPC-150-500
LPC-150-700
VOLTAGE TOLERANCE
±2.0%
IS 15885(Part 2/Sec13)
R-41027766
THOMAS SAMUEL
THOMAS SAMUEL
(for 700mA,1050mA,1400mA,2800mA only)
