LX7202-15ISF Datasheet LX7202-15ISF, LX7202-22ISF | P1-P3

LX7202-xx

PRODUCTION DATA SHEET

Microsemi

Analgo Mixed Signal Group

11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570

Page 1

WWW.Microsemi .COM

EMI Filter & ESD Protection for Up Stream USB

Ports

Rev. 1.0d, 2007-04-11

TM

®

DESCRIPTION

The LX7202 is an integrated

Universal Serial Bus (USB) line

termination device with an EMI filter

and ESD protection diodes. This

device offers a cost effective and

compact solution for one USB

upstream port. The USB specification

requires line termination resistors on

both the D+ and D- lines. These

resistors ensure signal integrity by

matching the cable impedance to that

of the differential driver. The 1.5 k

pull-up resistor identifies the

appropriate data line for full speed or

low speed operation.

The 47 pF capacitor completes the

high frequency filter and controls the

edge rate of the USB signals. The

LX7202 protects both D+ and D- data

lines and the voltage bus from ESD. The

TVS protection diodes exceed the

requirements of IEC61000-4-2, level 4,

15kV (air discharge) and 8kV (contact

discharge).The integrated configuration

of the LX7202 minimizes board space

and allows for ideal placement near the

connector. The LX7202 is ideal for use

in USB hubs, peripherals and portable

appliances.

IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com

PACKAGE ORDER INFO

T

J

(°C)

SF

Plastic

6-Pin SOT23

Package

Marking

Tape & Reel Quantity

(Reel Size)

-40 to 125 LX7202-15ISF 2021

-40 to 125 LX7202-22ISF 2022

3K (7inches)

Note: Append the letter “T” to the part number

For Tape & Reel Ordering

KEY FEATURES

 Bi-directional EMI/RFI low-pass

filter

 Line termination with integrated

ESD protection

 Low TVS operating voltage

(5.25V)

 Low leakage current

 Integrated single die

construction

 Available with 15 or 22Ω Series

Resistance

 Crosses from Semtech STF202

APPLICATIONS

 USB 1.1 and USB 2.0 Full

Speed Compliant

 Peripherals

 Computers and Printers

 Mobile phones

 Pagers and PDA’s

 Digital Cameras

BENEFITS

 Filter response characterized up

to 6 GHz

 <2dB insertion loss in the pass

band

 >20dB attenuation in the 800-

900 MHz range

 >12dB attenuation in the WLAN

frequencies of 2.4GHz and 5.0-

6.0 GHz

PRODUCT HIGHLIGHT

Rs

D out

to IC

V

BUS

1.5K

D in

from

connector

6

1

D in

from

connector

D out

to IC

47pF

Circuit Diagram

R

PU

R

S

C

R

S

C

16

5

4

3

2

V

BUS

D

IN

from

connector

D

OUT

to IC

GND

D

IN

from

connector

D

OUT

to IC

Functional Schematic with PinOut

L

X

7

2

0

2

-

X

LX7202-xx

PRODUCTION DATA SHEET

Microsemi

Analgo Mixed Signal Group

11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570

Page 2

WWW.Microsemi .COM

EMI Filter & ESD Protection for Up Stream USB

Ports

Rev. 1.0d, 2007-04-11

TM

®

ABSOLUTE MAXIMUM RATINGS

Steady State Power ...........................................................................100mW

ESD Air Discharge per IEC61000-4-2.................................................16KV

ESD Contact Discharge per IEC61000-4-2 .........................................10KV

Lead Soldering Temperature (10 Seconds)........................................ 260°C

Operating Temperature ...................................................... -40°C to +125°C

Storage Temperature Range............................................... -55°C to +150°C

Note: Exceeding these ratings could cause damage to the device. All voltages are with

respect to Ground. Currents are positive into, negative out of specified terminal

.

THERMAL DATA

SF

Plastic SOT-23 6-Pin

THERMAL RESISTANCE-JUNCTION TO CASE, θ

JC

62 °C/W

THERMAL RESISTANCE-JUNCTION TO AMBIENT, θ

JA

96 °C/W

Junction Temperature Calculation: T

J

= T

A

+ (P

D

x θ

JA

).

The θ

JA

numbers are guidelines for the thermal performance of the device/pc-board system. All

of the above assume no ambient airflow.

PACKAGE PIN OUT

V

BUS

D

IN

D

IN

D

OUT

D

OUT

GND

1

2

3

4

5

6

from

connector

from

connector

to IC

SF PACKAGE

(Top View)

FUNCTIONAL PIN DESCRIPTION

Name Description

VBUS Bus Voltage

DIN Data In

GND Ground

DOUT Data Out

ELECTRICAL CHARACTERISTICS

Unless otherwise specified, the following specifications apply over the operating ambient temperature -40°C ≤ T

A

≤ +125°C except where

otherwise noted.

LX7202-xx

Parameter Symbol Test Conditions

Min Typ Max

Units

Stand-Off Voltage VR

WM

5.25 V

Breakdown Voltage V

BR

IR = 1mA 6 V

Leakage Current I

R

VRWM = 5.25V, T = 25°C 1 µA

Series Resistance (-15) R

S

Each Line 13.5 15 16.5

Ω

Series Resistance (-22) R

S

Each Line 19.8 22 24.2

Ω

Temperature Coefficient of R

S

T

COEFF

Each Line 200 ppm

Pull Up Resistance R

PU

Each Line 1.35 1.5 1.65

K

Ω

Capacitor C Each Line 47 pF

Total Capacitance C

TOT

Between I/O Pins and Ground, Each Device

VR = 0V, f = 1MHz

54 60 66 pF

E

L

E

C

T

R

I

C

A

L

S

LX7202-xx

PRODUCTION DATA SHEET

Microsemi

Analgo Mixed Signal Group

11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570

Page 3

WWW.Microsemi .COM

EMI Filter & ESD Protection for Up Stream USB

Ports

Rev. 1.0d, 2007-04-11

TM

®

APPLICATION CIRCUITS

USB

Transceiver

Host or Hub (downstream) port Peripheral (upstream) port

USB

Transceiver

LX7201

LX7202

V

BUS

GND

16

5

4

3

2

R

PU

R

S

C

R

S

C

1

6

5

4

3

2

V

BUS

GND

C

R

S

R

PD

R

PD

R

S

C

Figure 1 – Typical Application

APPLICATION INFORMATION

The LX7202 meets the requirements of the USB v1.1 and

USB 2.0 Full Speed specification for device termination,

EMI filtering and ESD protection. The RS resistor provides

the proper signal termination; the 47pF capacitor controls

the signal rise and fall slew; the TVS diodes protect the IC

from ESD damage; and the total capacitance and resistance

creates a low pass filter eliminating the high frequency

energy from the circuit. The LX7202 can configure the

upstream port for either Full-Speed or Low-Speed

operation. The figures below show the proper connection in

accordance with the USB specification.

FULL SPEED DEVICE

The USB 2.0 specification offers a 12 Mbps data

transfer rate known as Full-Speed which requires a 1.5 k

pull-up resistor to be connected to the D+ line. Slew rate

control is accomplished with 47pF attached to the

transceiver before the R

S

.

 Voltage Supply (Vbus) is connected to Pin 1

 Ground is connected to Pin 6

 D+ from the connector is routed to Pin 3 (1.5 kΩ pull-up

resistor) and Pin 4 to the D+ line of the USB Transceiver

 D- from the connector is routed to Pin 2 and Pin 5 to the

D- line of the USB Transceiver

Peripheral

USB

Transceiver

GND

D+

D-

V

BUS

16

5

43

2

V

BUS

D

IN

D

IN

D

OUT

D

OUT

GND

LX7202

R

PU

cable

Host

USB

Transceiver

GND

D+

D-

V

BUS

Figure 2 – Connection for Full Speed Operation

A

P

L

I

C

A

T

I

O

N

S

LX7202-15ISF

LX7202-15ISF

Products related to this Datasheet