16
FN8118.3
December 9, 2015
ABSOLUTE MAXIMUM RATINGS
Temperature under bias .................... -65°C to +135°C
Storage temperature ......................... -65°C to +150°C
Voltage on any pin with
respect to V
SS
...................................... -1.0V to +7V
D.C. output current ............................................... 5mA
Lead temperature (soldering, 10 seconds)........ 300°C
COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only; the functional operation of the
device (at these or any other conditions above those
listed in the operational sections of this specification) is
not implied. Exposure to absolute maximum rating condi-
tions for extended periods may affect device reliability.
D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.)
Notes: (1) The device enters the active state after any start, and remains active until: 9 clock cycles later if the device select bits in the slave
address byte are incorrect; 200ns after a stop ending a read operation; or t
WC
after a stop ending a write operation.
(2) The device goes into standby: 200ns after any stop, except those that initiate a nonvolatile write cycle; t
WC
after a stop that initiates a
nonvolatile cycle; or 9 clock cycles after any start that is not followed by the correct device select bits in the slave address byte.
(3) V
IL
min. and V
IH
max. are for reference only and are not tested.
Symbol Parameter
V
CC
= 2.7 to 5.5V
Unit Test ConditionsMin. Max.
I
CC1
(1)
Active supply current read 1.0 mA V
IL
= V
CC
x 0.1, V
IH
= V
CC
x 0.9
f
SCL
= 400kHz
I
CC2
(1)
Active supply current write 3.0 mA
I
SB1
(2)
Standby current AC (WDT off) 1 µA V
IL
= V
CC
x 0.1, V
IH
= V
CC
x 0.9
f
SCL
= 400kHz, SDA = open
V
CC
= 1.22 x V
CC
min
I
SB2
(2)
Standby current DC (WDT off) 1 µA V
SDA
= V
SCL
= V
SB
Others = GND or V
SB
I
SB3
(2)
Standby current DC (WDT on) 20 µA V
SDA
=V
SCL
= V
SB
Others = GND or V
SB
I
LI
Input leakage current 10 µA V
IN
= GND to V
CC
I
LO
Output leakage current 10 µA V
SDA
= GND to V
CC
device is in standby
V
IL
(3)
Input LOW voltage -0.5 V
CC
x 0.3 V
V
IH
(3)
Input nonvolatile V
CC
x 0.7 V
CC
+ 0.5 V
V
HYS
Schmitt trigger input hysteresis
Fixed input level
V
CC
related level
0.2
.05 x V
CC
V
V
V
OL
Output LOW voltage 0.4 V I
OL
= 3.0mA (2.7-5.5V)
I
OL
= 1.8mA (2.0-3.6V)
RECOMMENDED OPERATING CONDITIONS
Temperature Min. Max.
Commercial 0°C 70°C
Industrial -40°C +85°C
Option Supply Voltage Limits
-2.7 and -2.7A 2.7V to 5.5V
Blank and -4.5A 4.5V to 5.5V
X4043, X4045