8
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT72T2098/108/118/128 2.5V HIGH-SPEED TeraSync™ DDR/SDR FIFO 20-BIT/10-BIT CONFIGURATIONS
32K x 20/64K x 10, 64K x 20/128K x 10, 128K x 20/256K x 10, 256K x 20/512K x 10
FEBRUARY 13, 2009
PIN NUMBER TABLE
Symbol Name I/O TYPE Pin Number
D0-19 Data Inputs HSTL-LVTTL D0-C3, D1-A4, D2-B4, D3-C4, D4-A5, D5-B5, D6-C5, D7-A6, D8-B6, D9-A7, D10-R7, D11-T7,
INPUT D12-R6, D13-T6, D14-R5, D15-T5, D16-R4, D17-T4, D18-P3, D19-R3
Q0-19 Data Outputs HSTL-LVTTL Q0-B10, Q1-A10, Q2-B11, Q3-A11, Q4-B12, Q5-A12, Q6-B13, Q7-A13, Q8-B14, Q9-A14, Q10-T14
OUTPUT Q11-R14, Q12-T13, Q13-R13, Q14-T12, Q15-R12, Q16-T11, Q17-R11, Q18-T10, Q19-R10
VCC +2.5V Supply INPUT A(1,2), C(6,7), D(4-7), K4, L4, M4, N(4-7), P(5-7), T(1,2)
VDDQ O/P Rail Voltage INPUT A(15,16), C(10-13), D(10-13), E13, F(4,13), G(4,14), H(4,14), J14, K14, L14, M13, N(10-13),
P(10-13), T(15,16)
GND Ground Pin INPUT A(8,9), B(8,9), C(8,9), D(8,9), E4, G(7-10,13), H(7-10,13), J(4,7-10,13), K(7-10,13), L13, N(8,9),
P(4,8,9), R(8,9), T(8,9)
DNC Do Not Connect — A3, B(1-3,15,16), C(1,2,14-16), D(1-3,14-16), E(1,15,16), K2, M(1-3,15,16), N(1-3,14-16), P(1,2,14-16),
R(1,2,15,16)
PIN DESCRIPTION (CONTINUED)
Symbol & Name I/O TYPE Description
Pin No.
WSDR
(1)
Write Single Data LVTTL When LOW, this input pin sets the write port to Single Data Clock mode. When HIGH, the write port will
(L1) Rate INPUT operate in Double Data Clock mode. This pin must be tied either HIGH or LOW and cannot toggle during
operation.
V
CC +2.5V Supply INPUT There are VCC supply inputs and must be connected to the 2.5V supply rail.
(See below)
VDDQ O/P Rail Voltage INPUT This pin should be tied to the desired voltage rail for providing power to the output drivers. Nominally 1.5V
(See below) or 1.8V for HSTL, 2.5V for LVTTL.
GND Ground Pin INPUT These are Ground pins are for the core device and must be connected to the GND rail.
(See below)
Vref Reference INPUT This is a Voltage Reference input and must be connected to a voltage level determined in the Recommended
(T3) Voltage DC Operating Conditions section. This provides the reference voltage when using HSTL class inputs.
If HSTL class inputs are not being used, this pin can be left floating.
NOTES:
1. Inputs should not change state after Master Reset.
2. These pins are for the JTAG port. Please refer to pages 24-27 and Figures 5-7.