MC10EP11, MC100EP11
www.onsemi.com
3
Table 3. MAXIMUM RATINGS
Symbol Parameter Condition 1 Condition 2 Rating Unit
V
CC
PECL Mode Power Supply V
EE
= 0 V 6 V
V
EE
NECL Mode Power Supply V
CC
= 0 V −6 V
V
I
PECL Mode Input Voltage
NECL Mode Input Voltage
V
EE
= 0 V
V
CC
= 0 V
V
I
v V
CC
V
I
w V
EE
6
−6
V
I
out
Output Current Continuous
Surge
50
100
mA
T
A
Operating Temperature Range −40 to +85 °C
T
stg
Storage Temperature Range −65 to +150 °C
q
JA
Thermal Resistance (Junction-to-Ambient) 0 lfpm
500 lfpm
SOIC−8NB 190
130
°C/W
q
JC
Thermal Resistance (Junction-to-Case) Standard Board SOIC−8NB 41 to 44 °C/W
q
JA
Thermal Resistance (Junction-to-Ambient) 0 lfpm
500 lfpm
TSSOP−8 185
140
°C/W
q
JC
Thermal Resistance (Junction-to-Case) Standard Board TSSOP−8 41 to 44 °C/W
q
JA
Thermal Resistance (Junction-to-Ambient) 0 lfpm
500 lfpm
DFN−8 129
84
°C/W
T
sol
Wave Solder (Pb-Free) <2 to 3 sec @ 260°C 265 °C
q
JC
Thermal Resistance (Junction-to-Case) (Note 1) DFN−8 35 to 40 °C/W
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. JEDEC standard multilayer board − 2S2P (2 signal, 2 power)
Table 4. 10EP DC CHARACTERISTICS, PECL (V
CC
= 3.3 V, V
EE
= 0 V (Note 1))
Symbol
Characteristic
−40°C 25°C 85°C
Min Typ Max Min Typ Max Min Typ Max Unit
I
EE
Negative Power Supply Current 20 29 37 20 30 39 22 31 40 mA
V
OH
Output HIGH Voltage (Note 2) 2165 2290 2415 2230 2355 2480 2290 2415 2540 mV
V
OL
Output LOW Voltage (Note 2) 1365 1490 1615 1430 1555 1680 1490 1615 1740 mV
V
IH
Input HIGH Voltage (Single-Ended) 2090 2415 2155 2480 2215 2540 mV
V
IL
Input LOW Voltage (Single-Ended) 1365 1690 1430 1755 1490 1815 mV
V
IHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration) (Note 3)
2.0 3.3 2.0 3.3 2.0 3.3 V
I
IH
Input HIGH Current 150 150 150
mA
I
IL
Input LOW Current
D
D
0.5
−150
0.5
−150
0.5
−150
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with V
CC
. V
EE
can vary +0.3 V to −2.2 V.
2. All loading with 50 W to V
CC
− 2.0 V.
3. V
IHCMR
min varies 1:1 with V
EE
, V
IHCMR
max varies 1:1 with V
CC
. The V
IHCMR
range is referenced to the most positive side of the differential
input signal.
