THD< 20% when output loading 70% at 230VAC input and output loading 80% at 277VAC input≧≧
37 units (circuit breaker of type B) / 37 units (circuit breaker of type C) at 115VAC
80 units (circuit breaker of type B) / 80 units (circuit breaker of type C) at 230VAC
THD< 20% when output loading 70% at 115VAC≧
SPECIFICATION
MODEL PCD-25-1400PCD-25-1050PCD-25-700PCD-25-350
RATED CURRENT
OPERATING VOLTAGE RANGE
RATED POWEROUTPUT
SETUP TIME
FREQUENCY RANGE
POWER FACTOR (Typ.)
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INPUT
INRUSH CURRENT(max.)
LEAKAGE CURRENT
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
SHORT CIRCUIT
OVER TEMPERATURE
1400mA1050mA700mA350mA
25.2W25.2W25.2W20.3W
2Vp-p2.2Vp-p2.7Vp-p4.6Vp-p
60V 50V 35V 25V
500ms / 230VAC 2000ms / 115VAC at full load
47 ~ 63Hz
PF>0.9/115VAC, PF>0.9/230VAC, PF>0.9/277VAC at full load (Please refer to "Power Factor Characteristic" curve)
80%80.5%81%82%
0.6A/115VAC 0.3A/230VAC 0.2A/277VAC
<0.5mA 120VAC / 240VAC
Hiccup mode, recovers automatically after fault condition is removed.
-30 ~ +60 (Refer to "Derating Curve")℃
20 ~ 95% RH non-condensing
-40 ~ +80 , 10 ~ 95% RH℃
±℃ ℃0.03%/ (0 ~ 50 )
10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes
906.5K hrs min. MIL-HDBK-217F (25 )℃
84*57*29.5mm (L*W*H)
0.19Kg; 72pcs/14.7Kg/0.92CUFT
25W Single OutputAC Dimmable LED Power Supply
■ Features :
PCD-25 series
RIPPLE & NOISE (max.) Note.1
ENVIRONMENT
SAFETY &
EMC
PROTECTION
Shut down o/p voltage, re-power on to recover
SAFETY STANDARDS
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3.75KVAC
I/P-O/P:100M Ohms / 500VDC / 25 / 70% RH℃
24 ~ 36V40 ~ 58V 12 ~ 18V16 ~ 24V
PCD-25-350 A A : With AC input 90~ 135VAC.
B : With AC input 180~ 295VAC.
File Name:PCD-25-SPEC 2018-01-12
1. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
2. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.
3. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently
connected to the mains.
UL8750, CSA C22.2 No. 250.0-08(except for PCD-25-350, PCD-25-700), ENEC EN613471, EN61347-2-13, EN62384(for B type only),
BIS IS15885(for 350B,700B only), EAC TP TC 004,IP42 approved ; design refer to UL60950-1, TUV EN60950-1, EN61347-1, EN61347-2-13
AC phase-cut dimming
Work with leading edge and trailing edge TRIAC dimmers
115VAC or 230VAC models available
Built-in active PFC function
Constant current design
Protections: Short circuit / Over temperature
Cooling by free air convection
Fully isolated plastic case
IP42 design
ⅡClass power unit, no FG
Class 2 power unit
Suitable for LED related fixture or appliance
(such as LED Decoration or Advertisement devices)
100% full load burn-in test
Low cost
High reliability
3 years warranty
NO LOAD OUTPUT VOLTAGE (max.)
±5.0%
Compliance to EN55015 (B type only), EN61000-3-2 Class C ; EN61000-3-3, FCC part 18 non-consumer equipment (A type only), EAC TP TC 020
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024,EN61547, light industry level, criteria A, EAC TP TC 020
EMC IMMUNITY
EMC EMISSION
CURRENT ACCURACY
COLD START 10A(t =20 s measured at 50% I ) at 115VAC / 230VAC
width peakμ
TOTAL HARMONIC
DISTORTION
MAX. No. of PSUs
on 16A CIRCUIT
BREAKER
A series
B series
A series
B series
SELV
( for A type only)
110
( for B type only)
( for B type only)
( for B type only)
( for B type only)
IP42
( except PCD-25-350/700 )
( for PCD-25-350/700 )
IS 15885(Part 2/Sec13)
R-41027766
THOMAS SAMUEL
THOMAS SAMUEL
( for 350B,700B only)
