12
FN8130.2
June 15, 2006
Absolute Maximum Ratings Recommended Operating Conditions
Temperature Under Bias . . . . . . . . . . . . . . . . . . . . .-65°C to +135°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Voltage on any Pin with Respect to V
SS
. . . . . . . . . . . . -1.0V to +7V
DC Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA
Lead Temperature (Soldering, 10s) . . . . . . . . . . . . . . . . . . . . . 300°C
Temperature Range
Commercial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C
Industrial. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
Supply Voltage Limits
-2.7 or -2.7A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7V to 5.5V
Blank or -4.5A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5V-5.5V
CAUTION: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; the functional
operation of the device (at these or any other conditions above those listed in the operational sections of this specification) is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability
DC Electrical Specifications Over the recommended operating conditions unless otherwise specified.
SYMBOL PARAMETER TEST CONDITIONS
LIMITS
UNITMIN TYP MAX
I
CC1
V
CC
write current (active) SCK = V
CC
x 0.1/V
CC
x 0.9 @ 2MHz,
SO = Open
5mA
I
CC2
V
CC
read current (active) SCK = V
CC
x 0.1/V
CC
x 0.9 @ 2MHz,
SO = Open
0.4 mA
I
SB
V
CC
standby current WDT = OFF CS = V
CC
, V
IN
= V
SS
or V
CC
,
V
CC
= 5.5V
1µA
I
LI
Input leakage current V
IN
= V
SS
to V
CC
0.110µA
I
LO
Output leakage current V
OUT
= V
SS
to V
CC
0.1 10 µA
V
IL
(NOTE 1)
Input LOW voltage -0.5 V
CC
x 0.3 V
V
IH
(NOTE 1)
Input HIGH voltage V
CC
x 0.7 V
CC
+ 0.5 V
V
OL1
Output LOW voltage V
CC
> 3.3V, I
OL
= 2.1mA 0.4 V
V
OL2
Output LOW voltage 2V < V
CC
3.3V, I
OL
= 1mA 0.4 V
V
OL3
Output LOW voltage V
CC
2V, I
OL
= 0.5mA 0.4 V
V
OH1
Output HIGH voltage V
CC
> 3.3V, I
OH
= -1.0mA V
CC
- 0.8 V
V
OH2
Output HIGH voltage 2V < V
CC
3.3V, I
OH
= -0.4mA V
CC
- 0.4 V
V
OH3
Output HIGH voltage V
CC
2V, I
OH
= -0.25mA V
CC
- 0.2 V
V
OLS
Reset output LOW voltage I
OL
= 1mA 0.4 V
Capacitance T
A
= +25°C, f = 1MHz, V
CC
= 5V.
SYMBOL TEST CONDITIONS MAX. UNIT
C
OUT
(NOTE 2)
Output capacitance (SO, RESET
/RESET) V
OUT
= 0V 8 pF
C
IN
(NOTE 2) Input capacitance (SCK, SI, CS, WP)V
IN
= 0V 6 pF
NOTES:
1. V
IL
min. and V
IH
max. are for reference only and are not tested.
2. This parameter is periodically sampled and not 100% tested.
X5168, X5169
