71
093016
F98-AS1 Series
Fused Face-Down, High CV
Capacitance Rated Voltage
*Cap
µF Code 10V (1A) 16V (1C) 20V (1D) 25V (1E) 35 (1V)
Code
1.0 105 M* M* M* SA
2.2 225 M* M* J
4.7 475 M* M* S
10 106 M* S a
22 226 M*/S J
33 336 M*/S n
47 476 S s
CAPACITANCE AND RATED VOLTAGE RANGE
(LETTER DENOTES CASE SIZE)
Available Ratings
*Codes under development – subject to change
Please contact to your local AVX sales office when these series
are being designed in your application.
TEST
F98-AS1 series (Temperature range -55ºC to +125ºC)
Condition
At 40°C, 90 to 95% R.H., 500 hours (No voltage applied)
Damp Heat Capacitance Change ........... Refer to the table above (*1)
(Steady State) Dissipation Factor ................ 150% or less of initial specified value
Leakage Current .................. 200% or less of initial specified value
-55°C / +125°C, 30 minutes each, 5 cycles
Temperature Cycles
Capacitance Change ........... Refer to the table above (*1)
Dissipation Factor ................ 150% or less of initial specified value
Leakage Current .................. 200% or less of initial specified value
10 seconds reflow at 260°C, 5 seconds immersion at 260°C.
Resistance to Capacitance Change ........... Refer to the table above (*1)
Soldering Heat Dissipation Factor ................ Initial specified value or less
Leakage Current .................. Initial specified value or less
After application of surge in series with a 1kΩ resistor at the rate of 30 seconds ON, 30 seconds OFF,
for 1000 successive test cycles at 85ºC, capacitors shall meet the characteristic requirements in the table above.
Surge Capacitance Change ........... Refer the table above (*1)
Dissipation Factor ................ 150% or less of initial specified value
Leakage Current .................. 200% or less of initial specified value
After 1000 hours’ application of rated voltage in series with a 3Ω resistor at 85°C,
capacitors shall meet the characteristic requirements in the table above.
Endurance Capacitance Change ........... Refer to the table above (*1)
Dissipation Factor ................ 150% or less of initial specified value
Leakage Current .................. 200% or less of initial specified value
Shear Test
After applying the pressure load of 5N for 10±1 seconds horizontally to the center of capacitor side body
which has no electrode and has been soldered beforehand on a substrate, there shall be found neither
exfoliation nor its sign at the terminal electrode.
Terminal Strength
Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at
both of the opposite bottom points 45mm apart from the center of capacitor, the pressure strength is
applied with a specified jig at the center of substrate so that the substrate may bend by 1mm as
illustrated. Then, there shall be found no remarkable abnormality on the capacitor terminals.
Fuse activation 5 seconds max. with 2A min. applied current
QUALIFICATION TABLE
RATINGS & PART NUMBER REFERENCE
*2: Leakage Current
After 5 minute’s application of rated voltage,
leakage current at 20ºC.
AVX Case Capacitance
Rated *2 DF ESR *1
Part No. Size (μF)
Voltage DCL @ 120Hz @ 100kHz ΔC/C
(V) (μA) (%) (Ω) (%)
10 Volt
F981A226MSAAS1 S 22 10 2.2 20 4.5 ±20
F981A336MSAAS1 S 33 10 3.3 30 6.5 ±30
F981A476MSAAS1 S 47 10 9.4 35 5.5 ±30
16 Volt
F981C106MSAAS1 S 10 16 1.6 18 4.5 ±20
35 Volt
F981V105MSAAS1 S 1 35 0.7 20 8.5 ±30
NOTICE: DESIGN, SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
