2
DF60 Series●65A 10.16mm pitch Wire-to-Board Connectors for Internal Power Supply(UL, C-UL, TÜV certified product)
■
Product Specifi cations
Ratings
Current
Rating
(Note 1)
No. of Contacts
8 AWG 10 AWG 12 AWG Operating Temperature
-
55
~
105ç (Note 2)
1 50A 40A 31A Operating Humidity Range
20
~
80
%
2
45A 35A 28A
Storage Temperature Range
-
10
~
60ç (Note 3)
3 Storage Humidity Range
40
~
70
%
4
42A 33A 27A
UL/TÜV fi le No. and certifi cation No.
UL
:
E52653
C-UL
:
E52653
TÜV
:
R50244085
5
6
Voltage Rating
AC/DC
1,000V
Current Rating Voltage Rating
UL See below table AC/DC
600V
C-UL
See upper table
(Δt=30
ç)
AC/DC
600V
TÜV See upper table AC/DC
600V
Current rating of
UL Standards
(Ambient temperature :
25ç)
(Note 1)
No. of Contacts
8 AWG 10 AWG 12 AWG
1
65A 55A
45A
2
40A
3
55A
50A
4
45A 35A5
6
Item Specifi cations Conditions
1. Insulation
resistance
No less than 1,000Mø Measured at DC=1,000V
2. Withstand
voltage
No fl ashover or breakdown AC 3,000V applied for 1 minute.
3. Contact
resistance
No more than 2mø Measured at 1A and not greater than 6V
4. Vibration
Resistance
No electrical discontinuity of 1μs or greater
Frequency 10 - 500Hz, accelerated velocity 98 m/s
2
,
2 hours for each of the three axis directions
5. Shock
Resistance
No electrical discontinuity of 1μs or greater
Accelerated velocity : 490m/s
2
, for11 ms, half-sine wave
form in 3 directions, 3 times for each of the three directions
6. Moisture-
resistance
Contact resistance : no more than 2mø ;
insulation resistance : no less than 1,000Mø
Temperature : 40±2ç; humidity : 90 to 95%, left for 96
hours
7. Temperature
cycles
Contact resistance : no more than 2mø ;
insulation resistance : no less than 1,000Mø
-55ç : 30 minutes
→
85ç : 30 minutes 25 cycles
8.Durability Contact resistance No more than 2mø 30 mating/unmating cycles
9. Solder heat
resistance
There should be no melting of the resin part
which will infl uence the performance.
Flow : 260ç, 10sec
Hand soldering : temperature of soldering iron at 350ç±10ç for 5 seconds
Note 1 : This is the maximum current rating while all pins are powered or used as all power lines. If you split the current over
multiple lines, please factor in your own safety margin.
Note 2 : Includes the temperature rise of power lines.
Note 3 : The storage condition refers to long-term storage of the product on the shelf before assembly. Please use the operating
temperature for temporary storage such as pre-assembly and during shipping.
■
Materials / Finish
Component Part Material Finish UL Specifi cation
Header
Insulator PBT (glass-reinforced) Black or gray UL94V-0
Contact
High conductivity copper
alloy
Gold plating
−
Metal fi tting Brass Tin-plating
−
Crimp socket Insulator PBT (glass-reinforced) Black or gray UL94V-0
In-line plug Insulator PBT (glass-reinforced) Black UL94V-0
Crimp contact Contact
High conductivity copper
alloy
Gold plating
−
Apr.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.