RE (ARE)
–5–
ASCTB104E 201407-T
• 75Ω type
NOTES
General tolerance: ±0.3 ±.012
20.2
2.54 0.5
(2.09)
7.62
(1.49)
11.2
(0.7)
(1.3)
8.6
0.3
9.6
13.2
±0.5
.520
±.020
0.3 0.3
.441
.339
.012
.378
.012 .012
(.082)(.059)
.795
.100 .020 .300
(.028)
(.511)
Note: Please consult us regarding recommended PC board patterns.
Schematic (Top view)
(Deenergized condition)
NOCOMNC
17
811 10 9121314
Direction indication
CAD Data
1. Coil operating power
Pure DC current should be applied to the
coil. The wave form should be
rectangular. If it includes ripple, the ripple
factor should be less than 5%.
However, check it with the actual circuit
since the characteristics may be slightly
different.
2. Cleaning
For automatic cleaning, the boiling
method is recommended. Avoid
ultrasonic cleaning which subjects the
relays to high frequency vibrations, which
may cause the contacts to stick.
It is recommended that alcoholic solvents
be used.
3. Soldering
(Standard PC board terminal)
1) The manual soldering shall be
performed under following condition.
Max. 260°C 500°F 10s
Max. 350°C 662°F 3s
The affect of the PCB on the relay will
differ depending on the type of PCB
used. Please verify the type of PCB to be
used.
Preheat according to the following
conditions.
Soldering should be done at 260±5°C
500±9°F within 6 s.
2) In case of automatic soldering, the
following conditions should be observed
(Surface-mount terminal)
(1) Position of measuring temperature
(2) IR (infrared reflow) soldering method
Temperature rise of relay itself may vary
according to the mounting level or the
heating method of reflow equipment.
Therefore, please set the temperature of
soldering portion of relay terminal and
the top surface of the relay case not to
exceed the above mentioned soldering
condition.
It is recommended to check the
temperature rise of each portion under
actual mounting condition before use.
4. Packing style
1) Tape dimensions
2) Dimensions of plastic reel
5. Conditions for operation, transport
and storage conditions
1) Ambient temperature, humidity, and
atmospheric pressure during usage,
transport, and storage of the relay:
(1) Temperature:
–40 to +70°C –40 to +158°F
(2) Humidity: 5 to 85% RH
(Avoid freezing and condensation.)
The humidity range varies with the
temperature. Use within the range
indicated in the graph below.
(3) Atmospheric pressure: 86 to 106 kPa
Temperature and humidity range for
usage, transport, and storage:
2) Condensation
Condensation forms when there is a
sudden change in temperature under
high temperature and high humidity
conditions. Condensation will cause
deterioration of the relay insulation.
3) Freezing
Condensation or other moisture may
freeze on the relay when the temperature
is lower than 0°C 32°F. This causes
problems such as sticking of movable
parts or operational time lags.
4) Low temperature, low humidity
environments
The plastic becomes brittle if the relay is
exposed to a low temperature, low
humidity environment for long periods of
time.
Temperature 120°C 248°F or less
Time Within 2 minute
A
A: Surface of PC board where relay is mounted.
T1
T2
T3
t1 t2
T1=
T
2=
T
3=
t
1=
t
2=
155 to 165°C
180 to 200°C
245°C max.
within 120s
within 30s
311 to 329°F
356 to 392°F
473°F max.
Tape coming out direction
Relay polarity bar
44
±0.3
2.0
±0.15
40.4
20.2
1.75
0.4
4
13.8520.0
1.5 .059
1.7
R0.75
20.75
10.6
+0.2
−0.3
.417
+.008
−.012
RE Relay
1.5
+0.1
−0 dia..059
+.004
−0
1.732
±.012
.079
±.006
1.591
.795
.069
.016
.157
.545.787
.067
.030
.817
380
±0.2
21
±0.8
dia.
13
±0.2
dia.
2.0
±0.5
Max. 95
Max. 51.7
45.5
+0.2
−0
1.791
+.008
−0
14.961
±.008
.827
±.031
dia.
.512
±.008
dia.
.079
±.020
3.740
2.035
For general cautions for use, please
refer to the “General Application
Guidelines”.
Humidity, %R.H.
Tolerance range
85
5
070–40
+32 +158–40
(Avoid
condensation
when used at
temperatures
higher than
0°C
(Avoid freezing
when used at
temperatures
lower than
0°C 32°F)
Temperature, °C °F
32°F)
