4
FN4071.12
September 20, 2006
Spurious Free Dynamic Range to Nyquist
(Note 4)
f
CLK
= 10 MSPS, f
OUT
= 1.023MHz, 5MHz Span - 86 - dBc
f
CLK
= 10 MSPS, f
OUT
= 2.02MHz, 5MHz Span - 85 - dBc
f
CLK
= 25 MSPS, f
OUT
= 2.02MHz, 12.5MHz Span - 77 - dBc
f
CLK
= 50 MSPS, f
OUT
= 5.055MHz, 25MHz Span - 74 - dBc
f
CLK
= 75 MSPS, f
OUT
= 7.52MHz, 37.5MHz Span - 73 - dBc
f
CLK
= 100 MSPS, f
OUT
= 10.1MHz, 50MHz Span - 71 - dBc
Multi-Tone Power Ratio
(MTPR)
8 Tones, no Clipping, 110kHz Spacing, 220kHz spacing
between tones 4 and 5, f
CLK
= 20 MSPS (Note 7)
-76-dBc
REFERENCE/CONTROL AMPLIFIER
Internal Reference Voltage, V
REF
(Note 5) -1.27 -1.23 -1.17 V
Internal Reference Voltage Drift (Note 4) - 50 - V/°C
Internal Reference Output Current Sink/Source
Capability
(Note 4) -500 - +50 A
Internal Reference Load Regulation I
REF
= 0 to I
REF
= -500A - 100 - V
Amplifier Input Impedance (Note 4) - 3 - M
Amplifier Large Signal Bandwidth 4.0V
P-P
Sine Wave Input, to Slew Rate Limited (Note 4) - 1 - MHz
Amplifier Small Signal Bandwidth 1.0V
P-P
Sine Wave Input, to -3dB Loss (Note 4) - 5 - MHz
Reference Input Impedance (CTL IN) (Note 4) - 12 - k
Reference Input Multiplying Bandwidth (CTL IN) R
L
= 50, 100mV Sine Wave, to -3dB Loss at I
OUT
(Note 4)
-75-MHz
DIGITAL INPUTS (D9-D0, CLK, INVERT)
Input Logic High Voltage, V
IH
(Note 5) 2.0 - - V
Input Logic Low Voltage, V
IL
(Note 5) - - 0.8 V
Input Logic Current, I
IH
(Note 5) - - 400 A
Input Logic Current, I
IL
(Note 5) - - 700 A
Digital Input Capacitance, C
IN
(Note 4) - 3.0 - pF
TIMING CHARACTERISTICS
Data Setup Time, t
SU
See Figure 1 (Note 4) 3 2.0 - ns
Data Hold Time, t
HLD
See Figure 1 (Note 4) 0.5 0.25 - ns
Propagation Delay Time, t
PD
See Figure 1 (Note 4) - 4.5 - ns
CLK Pulse Width, t
PW1
, t
PW2
See Figure 1 (Note 4) 1.0 0.85 - ns
POWER SUPPLY CHARACTERISTICS
IV
EEA
(Note 5) - 42 50 mA
IV
EED
(Note 5) - 75 95 mA
IV
CCD
(Note 5) - 13 20 mA
Power Dissipation (Note 5) - 650 - mW
Power Supply Rejection Ratio V
CC
5%, V
EE
5% - 5 - A/V
NOTES:
2. Dissipation rating assumes device is mounted with all leads soldered to printed circuit board.
3. Gain Error measured as the error in the ratio between the full scale output current and the current through R
SET
(typically 1.28mA). Ideally the
ratio should be 16.
4. Parameter guaranteed by design or characterization and not production tested.
5. All devices are 100% tested at +25°C.
6. Dynamic Range must be limited to a 1V swing within the compliance range.
7. In testing MTPR, tone frequencies ranged from 1.95MHz to 3.05MHz. The ratio is measured as the range from peak power to peak distortion in
the region of removed tones.
Electrical Specifications AV
EE
, DV
EE
= -4.94V to -5.46V, V
CC
= +4.75 to +5.25V, V
REF
= Internal,
T
A
= +25°C (Continued)
PARAMETER TEST CONDITIONS
HI5741BI
T
A
= -40°C TO +85°C
UNITSMIN TYP MAX
HI5741
