OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

MM74HC259N

P1-P3P4-P6P7-P7
September 1983
Revised February 1999
MM74HC259 8-Bit Addressable Latch/3-to-8 Line Decoder
© 1999 Fairchild Semiconductor Corporation DS005006.prf www.fairchildsemi.com
MM74HC259
8-Bit Addressable Latch/3-to-8 Line Decoder
General Description
The MM74HC259 device utilizes advanced silicon-gate
CMOS technology to implement an 8-bit addressable latch,
designed for general purpose storage applications in digital
systems.
The MM74HC259 has a single data input (D), 8 latch out-
puts (Q1–Q8), 3 address inputs (A, B, and C), a common
enable input (G
), and a common CLEAR input. To operate
this device as an addressable latch, data is held on the D
input, and the address of the latch into which the data is to
be entered is held on the A, B, and C inputs. When
ENABLE is taken LOW the data flows through to the
addressed output. The data is stored when ENABLE transi-
tions from LOW-to-HIGH. All unaddressed latches will
remain unaffected. With enable in the HIGH state the
device is deselected, and all latches remain in their previ-
ous state, unaffected by changes on the data or address
inputs. To eliminate the possibility of entering erroneous
data into the latches, the enable should be held HIGH
(inactive) while the address lines are changing.
If enable is held HIGH and CLEAR is taken LOW all eight
latches are cleared to a LOW state. If enable is LOW all
latches except the addressed latch will be cleared. The
addressed latch will instead follow the D input, effectively
implementing a 3-to-8 line decoder.
All inputs are protected from damage due to static dis-
charge by diodes to V
CC
and ground.
Features
■ Typical propagation delay: 18 ns
■ Wide supply range: 2–6V
■ Low input current: 1 µA maximum
■ Low quiescent current: 80 µA maximum (74HC Series)
Ordering Code:
Devices also available in Tape and Reel. Specify by appending the suffix letter “X” to the ordering code.
Connection Diagram
Pin Assignments for DIP, SOIC, SOP and TSSOP
Top View
Latch Selection Table
H = HIGH level, L = LOW level
D = the level at the data input
Q
i0
the level of Q
i
(i = 0, 1...7, as appropriate)
before the indicated steady-state input
conditions were established.
Order Number Package Number Package Description
MM74HC259M M16A 16-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-120, 0.150” Narrow
MM74HC259SJ M16D 16-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide
MM74HC259MTC MTC16 16-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide
MM74HC259N N16E 16-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300” Wide
Select Inputs Latch
C B A Addressed
LLL 0
LLH 1
LHL 2
LHH 3
HLL 4
HLH 5
HHL 6
HHH 7
www.fairchildsemi.com 2
MM74HC259
Truth Table
Logic Diagram
Inputs Outputs of Each
Addressed Other Function
Clear G
Latch Output
HL D Q
i0
Addressable Latch
HH Q
i0
Q
i0
Memory
L L D L 8-Line Decoder
L H L L Clear
3 www.fairchildsemi.com
MM74HC259
Absolute Maximum Ratings(Note 1)
(Note 2)
Recommended Operating
Conditions
Note 1: Absolute Maximum Ratings are those values beyond which dam-
age to the device may occur.
Note 2: Unless otherwise specified all voltages are referenced to ground.
Note 3: Power Dissipation temperature derating — plastic “N” package: −
12 mW/°C from 65°C to 85°C
DC Electrical Characteristics (Note 4)
Note 4: For a power supply of 5V ±10% the worst case output voltages (V
OH
, and V
OL
) occur for HC at 4.5V. Thus the 4.5V values should be used when
designing with this supply. Worst case V
IH
and V
IL
occur at V
CC
=5.5V and 4.5V respectively. (The V
IH
value at 5.5V is 3.85V.) The worst case leakage current
(I
IN
, I
CC
, and I
OZ
) occur for CMOS at the higher voltage and so the 6.0V values should be used.
Supply Voltage (V
CC
) −0.5 to +7.0V
DC Input Voltage (V
IN
) −1.5 to V
CC
+1.5V
DC Output Voltage (V
OUT
) −0.5 to V
CC
+0.5V
Clamp Diode Current (I
IK
, I
OK
) ±20 mA
DC Output Current, per pin (I
OUT
) ±25 mA
DC V
CC
or GND Current, per pin (I
CC
) ±50 mA
Storage Temperature Range (T
STG
) −65°C to +150°C
Power Dissipation (P
D
)
(Note 3) 600 mW
S.O. Package only 500 mW
Lead Temperature (T
L
)
(Soldering 10 seconds) 260°C
Min Max Units
Supply Voltage (V
CC
)26V
DC Input or Output Voltage 0 V
CC
V
(V
IN
, V
OUT
)
Operating Temperature Range (T
A
) −40 +85 °C
Input Rise or Fall Times
(t
r
, t
f
) V
CC
= 2.0V 1000 ns
V
CC
= 4.5V 500 ns
V
CC
= 6.0V 400 ns
Symbol Parameter Conditions
V
CC
T
A
= 25°CT
A
= −40 to 85°CT
A
= −55 to 125°C
Units
Typ Guaranteed Limits
V
IH
Minimum HIGH Level 2.0V 1.5 1.5 1.5 V
Input Voltage 4.5V 3.15 3.15 3.15 V
6.0V 4.2 4.2 4.2 V
V
IL
Maximum LOW Level 2.0V 0.5 0.5 0.5 V
Input Voltage 4.5V 1.35 1.35 1.35 V
6.0V 1.8 1.8 1.8 V
V
OH
Minimum HIGH Level V
IN
= V
IH
or V
IL
Output Voltage |I
OUT
| ≤ 20 µA 2.0V 2.0 1.9 1.9 1.9 V
4.5V 4.5 4.4 4.4 4.4 V
6.0V 6.0 5.9 5.9 5.9 V
V
IN
= V
IH
or V
IL
|I
OUT
| ≤ 4.0 mA 4.5V 4.2 3.98 3.84 3.7 V
|I
OUT
| ≤ 5.2 mA 6.0V 5.7 5.48 5.34 5.2 V
V
OL
Maximum LOW Level V
IN
= V
IH
or V
IL
Output Voltage |I
OUT
| ≤ 20 µA 2.0V 0 0.1 0.1 0.1 V
4.5V 0 0.1 0.1 0.1 V
6.0V 0 0.1 0.1 0.1 V
V
IN
= V
IH
or V
IL
|I
OUT
| ≤ 4.0 mA 4.5V 0.2 0.26 0.33 0.4 V
|I
OUT
| ≤ 5.2 mA 6.0V 0.2 0.26 0.33 0.4 V
I
IN
Maximum Input V
IN
= V
CC
or GND 6.0V ±0.1 ±1.0 ±1.0 µA
Current
I
CC
Maximum Quiescent V
IN
= V
CC
or GND 6.0V 8.0 80 160 µA
Supply Current I
OUT
= 0 µA
P1-P3P4-P6P7-P7

MM74HC259N

Mfr. #:
Buy MM74HC259N
Manufacturer:
ON Semiconductor / Fairchild
Description:
Latches 8-Bit Latch/Decoder
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet