4
FN6091.2
June 23, 2006
COM OFF Capacitance,
C
COM(OFF)
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, See Figure 6 25 - 182 - pF
COM ON Capacitance, C
COM(ON)
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, See Figure 6 25 - 290 - pF
POWER SUPPLY CHARACTERISTICS
Power Supply Range Full 1.65 - 3.6 V
Positive Supply Current, I+ V+ = 1.65V to 3.6V, V
IN
= 0V or V+, all channels on or
off
25 - - 30 nA
Full - - 750 nA
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, V
INL
Full - - 0.5 V
Input Voltage High, V
INH
Full 1.4 - - V
Input Current, I
INH
, I
INL
V+ = 3.3V, V
IN
= 0V or V+ (Note 7) Full -0.5 - 0.5 A
NOTES:
4. V
IN
= input voltage to perform proper function.
5. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
6. Parts are 100% tested at +25°C. Limits across the full temperature range are guaranteed by design and correlation.
7. Guaranteed but not tested.
8. R
ON
matching between channels is calculated by subtracting the channel with the highest max Ron value from the channel with lowest max Ron
value.
9. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range.
Electrical Specifications - 1.8V Supply Test Conditions: V+ = +1.65V to +2.0V, GND = 0V, V
INH
= 1.0V, V
INL
= 0.4V (Note 4, 6),
Unless Otherwise Specified
PARAMETER TEST CONDITIONS
TEMP
(°C)
MIN
(NOTE 5) TYP
MAX
(NOTE 5)UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
Full 0 - V+ V
ON Resistance, R
ON
V+ = 1.8V, I
COM
= 100mA, V
NO
or V
NC
= 0V to V+, See
Figure 4, Note 7
25 - 0.26 0.35
Full - - 0.4
R
ON
Matching Between Channels,
R
ON
V+ = 1.8V, I
COM
= 100mA, V
NO
or V
NC
= Voltage at
Max R
ON,
Note 8
25 - 0.005 -
Full - 0.005 -
R
ON
Flatness, R
FLAT(ON)
V+ = 1.8V, I
COM
= 100mA, V
NO
or V
NC
= 0V to V+,
Note 9
25 - 0.074 -
Full - 0.082 -
NO or NC OFF Leakage Current,
I
NO(OFF)
or I
NC(OFF)
V+ = 2.0V, V
COM
= 0.3V, 1.8V, V
NO
or V
NC
= 1.8V, 0.3V 25 -3 - 3 nA
Full -60 - 60 nA
COM ON Leakage Current,
I
COM(ON)
V = 2.0V, V
COM
= 0.3V, 1.8V, or V
NO
or V
NC
= 0.3V,
1.8V
25 -3 - 3 nA
Full -80 - 80 nA
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
ON
V = 1.65V, V
NO
or V
NC
= 1.0V, R
L
=50, C
L
= 35pF,
V
IN
= 0 to 1.65V, See Figure 1, Note 7
25 - 30 40 ns
Full - - 45 ns
Turn-OFF Time, t
OFF
V = 1.65V, V
NO
or V
NC
= 1.0V, R
L
=50, C
L
= 35pF,
V
IN
= 0 to 1.65V, See Figure 1, Note 7
25 - 25 35 ns
Full - - 40 ns
Charge Injection, Q C
L
= 1.0nF, V
G
= 0V, R
G
= 0See Figure 2 25 - -80 - pC
Electrical Specifications - 3V Supply Test Conditions: V+ = +2.7V to +3.3V, GND = 0V, V
INH
= 1.4V, V
INL
= 0.5V (Note 4, 6),
Unless Otherwise Specified (Continued)
PARAMETER TEST CONDITIONS
TEMP
(°C)
MIN
(NOTE 5) TYP
MAX
(NOTE 5) UNITS
ISL43L120, ISL43L121, ISL43L122