TLE7276-2
Pin Configuration
Data Sheet 4 Rev. 1.0, 2009-06-01
3 Pin Configuration
3.1 Pin Assignment PG-SSOP-14 Exposed Pad
Figure 2 Pin Configuration (top view)
3.2 Pin Definitions and Functions PG-SSOP-14 Exposed Pad
Pin No. Symbol Function
1,2,3,5,7 n.c. non connected
can be open or connected to GND
4GNDGround
6ENEnable Input
high level input signal enables the IC;
low level input signal disables the IC;
integrated pull-down resistor
8,10,11,12,14 n.c. non connected
can be open or connected to GND
9QOutput
block to ground with a capacitor close to the IC terminals, respecting the values given
for its capacitance and ESR in “Functional Range” on Page 6
13 I Input
block to ground directly at the IC with a ceramic capacitor
Pad Exposed Pad
connect to GND and heatsink area
QF
QF
4
QF
QF
QF
,
QF
QF
(1
QF
*1'
QF
QF





7/(B3,1&21),*B6623
69*
Data Sheet 5 Rev. 1.0, 2009-06-01
TLE7276-2
Pin Configuration
3.3 Pin Assignment PG-TO252-5
Figure 3 Pin Configuration (top view)
3.4 Pin Definitions and Functions PG-TO252-5
Pin No. Symbol Function
1IInput
block to ground directly at the IC with a ceramic capacitor
2n.c.non connected
can be open or connected to GND
3GNDGround
internally connected to heat slug
4ENEnable Input
high level input signal enables the IC;
low level input signal disables the IC;
integrated pull-down resistor
5QOutput
block to ground with a capacitor close to the IC terminals, respecting the values given
for its capacitance and ESR in “Functional Range” on Page 6
Heat Slug Heat Slug
internally connected to GND;
connect to GND and heatsink area
n.c.
EN
Q
GND
I
TLE7276-2
General Product Characteristics
Data Sheet 6 Rev. 1.0, 2009-06-01
4 General Product Characteristics
4.1 Absolute Maximum Ratings
Note: Stresses above the ones listed here may cause permanent damage to the device. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
Note: Integrated protection functions are designed to prevent IC destruction under fault conditions described in the
data sheet. Fault conditions are considered as “outside” normal operating range. Protection functions are
not designed for continuous repetitive operation.
4.2 Functional Range
Note: Within the functional or operating range, the IC operates as described in the circuit description. The electrical
characteristics are specified within the conditions given in the Electrical Characteristics table.
Absolute Maximum Ratings
1)
T
j
= -40 °C to 150 °C; all voltages with respect to ground, (unless otherwise specified)
1) not subject to production test, specified by design
Pos. Parameter Symbol Limit Values Unit Test Condition
Min. Max.
Input I
4.1.1 Voltage
V
I
-0.3 45 V
Output Q
4.1.2 Voltage
V
Q
-0.3 6 V
4.1.3 Voltage
V
Q
-0.3 6.2 V t < 10 s
2)
2) exposure to these absolute maximum ratings for extended periods (t > 10 s) may affect device reliability
Enable Input EN
4.1.4 Voltage
V
EN
-0.3 45 V
Temperature
4.1.5 Junction temperature
T
j
-40 150 °C–
4.1.6 Storage temperature
T
stg
-50 150 °C–
ESD Susceptibility
4.1.7 Human Body Model (HBM)
3)
3) ESD susceptibility Human Body Model “HBM” according to AEC-Q100-002 - JESD22-A114
Voltage - 3 kV
4.1.8 Charged Device Model (CDM)
4)
4) ESD susceptibility Charged Device Model “CDM” according to ESDA STM5.3.1
Voltage - 1.5 kV
Pos. Parameter Symbol Limit Values Unit Remarks
Min. Max.
4.2.1 Input voltage
V
I
5.5 42 V
4.2.2 Output Capacitor’s
Requirements
C
Q
470 nF
1)
1) the minimum output capacitance requirement is applicable for a worst case capacitance tolerance of 30%
4.2.3 ESR(C
Q
) –10
2)
2) relevant ESR value at f =10kHz
4.2.4 Junction temperature T
j
-40 150 °C–

TLE72762EXUMA1

Mfr. #:
Manufacturer:
Infineon Technologies
Description:
IC REG LINEAR 5V 300MA 14SSOP
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet