NFZ2MSM601SN10L Datasheet NFZ2MSM101SN10L, NFZ2MSM181SN10L, NFZ2MSM301SN10L | P1-P3

Spec No. JENF243J-0002A-01 P1/8

MURATA MFG.CO., LTD

Reference

Only

CHIP NOISE FILTER NFZ2MSM□□□SN10L REFERENCE SPECIFICATION

1. Scope

This reference specification applies to NFZ2MSM_SN10L, Chip Noise Filter.

2. Part Numbering

(ex) NF Z 2M S M 181 S N 1 0 L

Product ID Structure Dimension Characteristics Typical Impedance Performance Category Numbers special Packaging

(L×W) at 100MHz of speci- L:Taping

Circuit fication *B: BULK

*B: Bulk packing also available

3. Rating

・Operating Temperature Range – 40°C to + 85°C

・Storage Temperature Range – 40°C to + 85°C

*1: When applied Rated current to the Products, self temperature rise shall be limited to 40℃ max.

Typical value is actual performance.

4. Testing Conditions

《Unless otherwise specified》《In case of doubt》

Temperature : Ordinary Temperature / 15°C to 35°C Temperature

: 20°C ± 2°C

Humidity

: Ordinary Humidity / 25%(RH) to 85%(RH) Humidity : 60%(RH) to 70%(RH)

Atmospheric Pressure : 86kPa to 106kPa

5. Appearance and Dimensions

■Unit Mass (Typical value)

0.012g

(in mm)

Customer

Part Number

MURATA

Part Number

Impedance at 100MHｚ

DC Resistance

(mΩ)

Rated Current *1

(A)

(Ω) Tolerance Typ. Max.

NFZ2MSM101SN10L 100

±25%

14 18 4.0

NFZ2MSM181SN10L 180 20 25 3.4

NFZ2MSM301SN10L 300 24 30 3.1

NFZ2MSM601SN10L 600 37 46 2.5

0.5 ± 0.2

2.0 ± 0.2

1.6 ± 0.2

0.9 ± 0.1

Spec No. JENF243J-0002A-01 P2/8

MURATA MFG.CO., LTD

Reference

Only

6. Electrical Performance

No. Item Specification Test Method

6.1 Impedance

Impedance shall meet item 3. Measuring Equipment:

Agilent 4991A or equivalent

(1mA)

Measuring Frequency: 100MHz

6.2 DC Resistance DC Resistance shall meet item 3. Measuring Equipment: Digital multi meter

DC resistance shall be measured after putting chip

noise filter between the terminal 2 under the condition

of opening between a and b.

Every measurement the terminal 1 shall be shorted

between a and b when changing noise filter.

7. Mechanical Performance

No. Item Specification Test Method

7.1 Shear Test Chip noise filter shall not be damaged

after tested as follows.

Applied Direction

Force: 10N

Hold Duration: 5s±1s

Applied Direction: Parallel to PCB

7.2 Bending Test

Substrate: Glass-epoxy substrate

(100mm×40mm×1.0mm)

Solder: Reflow

(in mm)

Speed of Applying Force: 0.5mm / s

Deflection: 2mm

Hold Duration: 30 s

7.3 Vibration Oscillation Frequency:

10Hz to 2000Hz to 10Hz for 20 min

Total amplitude 3.0 mm or Acceleration

amplitude 245m/s

whichever is smaller.

Testing Time:

A period of 4h in each of 3 mutually

perpendicular directions.

7.4 Drop It shall be dropped on concrete or steel

board.

Method : free fall

Height : 1m

Total of 10 cycles

Digital multi meter

(TR6846 or equivalent)

terminal2terminal1

Pressure jig

Deflection

Product

R230

Chip Coil

Substrate

Chip Noise Filter

Spec No. JENF243J-0002A-01 P3/8

MURATA MFG.CO., LTD

Reference

Only

No. Item Specification Test Method

7.5 Solderability The wetting area of the electrode

shall be at least 90% covered with

new solder coating.

Flux: Ethanol solution of rosin 25(wt)%

(Immersed for 5s to 10s)

Solder: Sn-3.0Ag-0.5Cu

Pre-Heating: 150°C±10°C / 60s to 90s

Solder Temperature: 240°C±5°C

Immersion Time: 3s±1s

7.6 Resistance to

Soldering Heat

Appearance: No damage

Impedance Change: within ±30%

Flux: Ethanol solution of rosin 25(wt)%

(Immersed for 5s to 10s)

Solder: Sn-3.0Ag-0.5Cu

Pre-Heating: 150°C±10°C / 60s to 90s

Solder Temperature: 270°C±5°C

Immersion Time: 10s±1s

Then measured after exposure in the room

condition for 24h±2h.

8. Environmental Performance

It shall be soldered on the substrate.

No. Item Specification Test Method

8.1 Heat Resistance Appearance: No damage

Impedance Change: within ±30%

Temperature: 85°C±2°C

Time: 1000h (+48h,-0h)

Then measured after exposure in the room

condition for 24h±2h.

8.2 Cold Resistance Temperature: -40°C±2°C

Time: 1000h (+48h,-0h)

Then measured after exposure in the room

condition for 24h±2h.

8.3 Humidity Temperature: 40°C±2°C

Humidity: 90%(RH) to 95%(RH)

Time: 1000h (+48h,-0h)

Then measured after exposure in the room

condition for 24h±2h.

8.4 Temperature

Cycle

1 cycle:

1 step: -40°C±2°C / 30 min±3 min

2 step: Ordinary temp. / 10 min to 15 min

3 step: 85°C±2°C / 30 min to 3 min

4 step: Ordinary temp. / 10 min to15 min

Total of 100cycles

Then measured after exposure in the room

condition for 24h±2h.

P1-P3 P4-P6 P7-P8

NFZ2MSM601SN10L

Mfr. #:

Buy NFZ2MSM601SN10L

Manufacturer:

Description:

EMI Filter Beads, Chips & Arrays 600ohm 2.5A +/-25% 2.0 x 1.6mm +/-0.2mm

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

NFZ2MSM601SN10L

NFZ2MSM601SN10L

Products related to this Datasheet