www.ams.com/LED-Driver-ICs/AS1110 Revision 1.6 19 - 24
AS1110
Datasheet - Application Information
9.3 Constant Current
In LED display applications, the AS1110 provides virtually no current variations from channel-to-channel and from AS1110-to-AS1110. This is
mostly due to 2 factors:
While IOUT ≥ 10mA, the maximum current skew is less than ±3% between channels and less than ±6% between AS1110 devices.
In the saturation region, the characteristic curve of the output stage is flat (see Figure 5 on page 7). Thus, the output current can be kept
constant regardless of the variations of LED forward voltages (V
F).
9.4 Adjusting Output Current
The AS1110 scales up the reference current (IREF) set by external resistor (REXT) to sink a current (IOUT) at each output port. As shown in
Figure 3 on page 7 the output current in the saturation region is extremely flat so that it is possible to define it as target current (I
OUT TARGET).
I
OUT TARGET can be calculated by:
V
REXT = 1.253V (EQ 1)
IREF = VREXT/REXT (if the other end of REXT is connected to ground) (EQ 2)
I
OUT TARGET = IREF*15 = (1.253V/REXT)*15 (EQ 3)
Where:
R
EXT is the resistance of the external resistor connected to pin REXT.
VREXT is the voltage on pin REXT.
The magnitude of current (as a function of R
EXT) is around 50.52mA at 372Ω and 25.26mA at 744Ω. Figure 3 on page 7 shows the relationship
curve between the I
OUT TARGET of each channel and the corresponding external resistor (REXT).
9.5 Package Power Dissipation
The maximum allowable package power dissipation (PD) is determined as:
P
D(MAX) = (TJ-TAMB)/RTH(J-A) (EQ 4)
When 16 output channels are turned on simultaneously, the actual package power dissipation is:
P
D(ACT) = (IDD*VDD) + (IOUT*Duty*VDS*16) (EQ 5)
Therefore, to keep PD(ACT) ≤ PD(MAX), the maximum allowed output current as a function of duty cycle is:
I
OUT = {[(TJ-TAMB)/RTH(J-A)]-(IDD*VDD)}/VDS/Duty/16 (EQ 6)
Where:
T
J = 150ºC
9.6 Delayed Outputs
The AS1110 has graduated delay circuits between outputs. These delay circuits can be found between OUTNn and constant current block.
The fixed delay time is 20 ns (typ) where OUTN0 has no delay, OUTN1 has 20ns delay, OUTN2 has 40ns delay ... OUTN15 has 300ns delay.
This delay prevents large inrush currents, which reduce power supply bypass capacitor requirements when the outputs turn on (see Figure 11 on
page 10)
9.7 Switching-Noise Reduction
LED drivers are frequently used in switch-mode applications which normally exhibit switching noise due to parasitic inductance on the PCB.
9.8 Load Supply Voltage
Considering the package power dissipation limits (see EQ 4:6), the AS1110 should be operated within the range of
VDS = 0.4 to 1.0V.
For example, if V
LED is higher than 5V, VDS may be so high that PD(ACT) > PD(MAX) where VDS = VLED - VF. In this case, the lowest possible
supply voltage or a voltage reducer (V
DROP) should be used. The voltage reducer allows
V
DS = (VLED -VF) - VDROP.
Note: Resistors or zener diodes can be used as a voltage reducer as shown in Figure 23.