OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

AT25010-10PC-2.7

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P16
1
Features
•
Serial Peripheral Interface (SPI) Compatible
•
Supports SPI Modes 0 (0,0) and 3 (1,1)
•
Low-Voltage and Standard-Voltage Operation
– 5.0 (V
CC
= 4.5V to 5.5V)
– 2.7 (V
CC
= 2.7V to 5.5V)
– 1.8 (V
CC
= 1.8V to 3.6V)
•
2.1 MHz Clock Rate (5V) Compatibility
•
8-Byte Page Mode
•
Block Write Protection
– Protect 1/4, 1/2, or Entire Array
•
Write Protect (WP) Pin and Write Disable Instructions for
Both Hardware and Software Data Protection
•
Self-Timed Write Cycle (10 ms max)
•
High Reliability
– Endurance: 1 Million Write Cycles
– Data Retention: 100 Years
– ESD Protection: >4000V
•
Automotive Grade and Extended Temperature Devices Available
•
8-Pin PDIP and JEDEC SOIC Packages
Description
The AT25010/020/040 provides 1024/2048/4096 bits of serial electrically erasable
programmable read only memory (EEPROM) organized as 128/256/512 words of 8
bits each. The device is optimized for use in many industrial and commercial applica-
tions where low power and low voltage operation are essential. The AT25010/020/040
is available in space saving 8-pin PDIP and 8-pin JEDEC (SOIC) packages.
The AT25010/020/040 is enabled through the Chip Select pin (CS
) and accessed via
a 3-wire interface consisting of Serial Data Input (SI), Serial Data Output (SO), and
Serial Clock (SCK). All programming cycles are completely self-timed, and no sepa-
rate ERASE cycle is required before WRITE.
BLOCK WRITE protection is enabled by programming the status register with one of
four blocks of write protection. Separate program enable and program disable instruc-
tions are provided for additional data protection. Hardware data protection is provided
via the WP
pin to protect against inadvertent write attempts. The HOLD pin may be
used to suspend any serial communication without resetting the serial sequence.
SPI Serial
EEPROMs
1K (128 x 8)
2K (256 x 8)
4K (512 x 8)
AT25010
AT25020
AT25040
Rev. 0606E–08/98
SPI, 1K Serial
E
2
PROM
Pin Configurations
Pin Name Function
CS
Chip Select
SCK Serial Data Clock
SI Serial Data Input
SO Serial Data Output
GND Ground
VCC Power Supply
WP
Write Protect
HOLD Suspends Serial Input
8-Pin PDIP
1
2
3
4
8
7
6
5
CS
SO
WP
GND
VCC
HOLD
SCK
SI
8-Pin SOIC
1
2
3
4
8
7
6
5
CS
SO
WP
GND
VCC
HOLD
SCK
SI
AT25010/020/040
2
Block Diagram
Absolute Maximum Ratings*
Operating Temperature................................. -55°C to + 125°C
*NOTICE: Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent dam-
age to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect
device reliability.
Storage Temperature .................................... -65°C to + 150°C
Voltage on Any Pin
with Respect to Ground....................................-1.0V to + 7.0V
Maximum Operating Voltage........................................... 6.25V
DC Output Current........................................................ 5.0 mA
AT25010/020/040
3
Note: 1. This parameter is characterized and is not 100% tested.
Notes: 1. This parameter is preliminary and Atmel may change the specifications upon further characterization.
2. V
IL
min and V
IH
max are reference only and are not tested.
Pin Capacitance
(1)
Applicable over recommended operating range from T
A
= 25°C, f = 1.0 MHz, V
CC
= +5.0V (unless otherwise noted).
Symbol Test Conditions Max Units Conditions
C
OUT
Output Capacitance (SO) 8 pF V
OUT
= 0V
C
IN
Input Capacitance (CS, SCK, SI, WP, HOLD)6pFV
IN
= 0V
DC Characteristics
Applicable over recommended operating range from: T
AI
= -40°C to +85°C, V
CC
= +1.8V to +5.5V, T
AC
= 0°C to +70°C,
V
CC
= +1.8V to +5.5V (unless otherwise noted).
Symbol Parameter Test Condition Min Max Units
V
CC1
(1)
Supply Voltage 1.8 5.5 V
V
CC2
Supply Voltage 2.7 5.5 V
V
CC3
Supply Voltage 4.5 5.5 V
I
CC1
Supply Current V
CC
= 5.0V at 1 MHz, SO = Open 3.0 mA
I
CC2
Supply Current V
CC
= 5.0V at 2 MHz, SO = Open 6.0 mA
I
SB1
(1)
Standby Current V
CC
= 1.8V CS = V
CC
100 µA
I
SB2
Standby Current V
CC
= 2.7V CS = V
CC
100 µA
I
SB3
Standby Current V
CC
= 5.0V CS = V
CC
100 µA
I
IL
Input Leakage V
IN
= 0V to V
CC
-0.6 3.0 µA
I
OL
Output Leakage V
IN
= 0V to V
CC
, T
AC
= 0°C to 70°C-0.63.0µA
V
IL
(2)
Input Low Voltage -0.6 V
CC
x 0.3 V
V
IH
(2)
Input High Voltage V
CC
x 0.7 V
CC
+ 0.5 V
V
OL1
Output Low Voltage
4.5V ≤ V
CC
≤ 5.5V
I
OL
= 2.0 mA 0.4 V
V
OH1
Output High Voltage I
OH
= -1.0 mA V
CC
- 0.8 V
V
OL2
Output Low Voltage
1.8V ≤ V
CC
≤ 3.6V
I
OL
= 0.15 mA 0.2 V
V
OH2
Output High Voltage I
OH
= -100 µAV
CC
- 0.2 V
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P16

AT25010-10PC-2.7

Mfr. #:
Buy AT25010-10PC-2.7
Manufacturer:
Description:
IC EEPROM 1K SPI 3MHZ 8DIP
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet