OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

ADG804YRM

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P17
ADG804 Data Sheet
Rev. A | Page 6 of 16
ABSOLUTE MAXIMUM RATINGS
T
A
= 25°C, unless otherwise noted.
Table 4.
Parameter Rating
V
DD
to GND −0.3 V to +4.6 V
Analog Inputs
1
−0.3 V to V
DD
+ 0.3 V
Digital Inputs
1
−0.3 V to +4.6 V or 10 mA,
whichever occurs first
Peak Current, S or D (Pulsed at 1 ms, 10% Duty
Cycle Max)
3.3 V Operation
500 mA
2.5 V Operation 460 mA
1.8 V Operation 420 mA
Continuous Current, S or D
3.3 V Operation 300 mA
2.5 V Operation 275 mA
1.8 V Operation 250 mA
Operating Temperature Range
Automotive (Y Version) −40°C to +125°C
Storage Temperature Range −65°C to +150°C
Junction Temperature 150°C
MSOP Package
θ
JA
Thermal Impedance 206°C/W
θ
JC
Thermal Impedance 44°C/W
Lead Temperature, Soldering As per JEDEC J-STD-020
1
Overvoltages at IN, S, or D are clamped by internal diodes. Current should be
limited to the maximum ratings given.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those listed in the operational sections
of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability. Only one absolute maximum rating may be
applied at any one time.
Table 5. ADG804 Truth Table
A1 A0 EN ON Switch
x x 0 None
0 0 1 S1
0 1 1 S2
1 0 1 S3
1
1
1
S4
ESD CAUTION
Data Sheet ADG804
Rev. A | Page 7 of 16
PIN CONFIGURATION
NC = NO CONNECT
ADG804
TOP VIEW
(Not to Scale)
A0
1
S1
2
GND
3
S3
4
EN
5
A1
S2
D
S4
V
DD
10
9
8
7
6
04307-0-002
Figure 2. 10-Lead MSOP (RM-10)
Table 6. Terminology
V
DD
Most positive power supply potential.
I
DD
Positive supply current.
GND Ground (0 V) reference.
S Source terminal. May be an input or an output.
D Drain terminal. May be an input or an output.
EN Active high logic control input.
A0, A1 Logic control inputs. Used to select which source terminal, S1 to S4, is connected to the drain, D.
V
D
, V
S
Analog voltage on terminals D, S.
R
ON
Ohmic resistance between D and S.
R
FLAT (ON)
Flatness is defined as the difference between the maximum and minimum value of on resistance as measured over the
specified analog signal range.
∆R
ON
On resistance match between any two channels.
I
S
(OFF) Source leakage current with the switch off.
I
D
(OFF) Drain leakage current with the switch off.
I
D
, I
S
(ON)
Channel leakage current with the switch on.
V
INL
Maximum input voltage for Logic 0.
V
INH
Minimum input voltage for Logic 1.
I
INL
(I
INH
) Input current of the digital input.
C
S
(OFF) Off switch source capacitance. Measured with reference to ground.
C
D
(OFF) Off switch drain capacitance. Measured with reference to ground.
C
D
, C
S
(ON) On switch capacitance. Measured with reference to ground.
C
IN
Digital input capacitance.
t
ON
(EN) Delay time between the 50% and the 90% points of the digital input and switch on condition.
t
OFF
(EN) Delay time between the 50% and the 90% points of the digital input and switch off condition.
t
TRANSITION
Delay time between the 50% and the 90% points of the digital input and switch on condition when switching from one
address state to the other.
t
BBM
On or off time measured between the 80% points of both switches when switching from one to another.
Charge Injection A measure of the glitch impulse transferred from the digital input to the analog output during on-off switching.
Off Isolation A measure of unwanted signal coupling through an off switch.
Crosstalk A measure of unwanted signal which is coupled through from one channel to another as a result of parasitic capacitance.
−3 dB Bandwidth
The frequency at which the output is attenuated by 3 dB.
On Response The frequency response of the on switch.
Insertion Loss The loss due to the on resistance of the switch.
THD + N The ratio of the harmonic amplitudes plus noise of a signal to the fundamental.
ADG804 Data Sheet
Rev. A | Page 8 of 16
TYPICAL PERFORMANCE CHARACTERISTICS
V
DD
= 3V
V
DD
= 2.7V
V
DD
= 3.3V
V
DD
= 3.6V
0.60
0.55
0.50
0.45
0.40
0.35
0
ON RESISTANCE ()
0.30
0.25
0.20
0.5 1.0 1.5 2.0 2.5
V
D
, V
S
(V)
3.0
3.5
04307-0-004
T
A
= 25°C
Figure 3. On Resistance vs. V
D
(V
S
) V
DD
= 2.7 V to 3.6 V
1.2
1.0
0.8
0.6
0.4
0.3
0.2
0.5 1.0 1.5 2.0 2.50
V
D
, V
S
(V)
ON RESISTANCE ()
V
DD
= 2.3V
T
A
= 25°C
V
DD
= 2.7V
V
DD
= 2.5V
04307-0-005
Figure 4. On Resistance vs. V
D
(V
S
) V
DD
= 2.5 V ± 0.2 V
1.4
1.2
1.0
0.8
0.6
0.2
0.2 1.0 1.2 1.4 1.80
V
D
, V
S
(V)
ON RESISTANCE ()
0.4
0.4 0.6 0.8 1.6
1.6
1.8
T
A
= 25
°C
V
DD
= 1.95V
04307-0-006
V
DD
= 1.8V
V
DD
= 1.65V
Figure 5. On Resistance vs. V
D
(V
S
) V
DD
= 1.8 ± 0.15 V
1.2
1.0
0.8
0.6
0.4
0.3
0
ON RESISTANCE ()
0.5 1.0 1.5 2.0 2.50
V
D
, V
S
(V)
3.0
V
DD
= 3.3V
–
40
°C
+25
°C
+85
°C
+125
°C
04307-0-007
Figure 6. On Resistance vs. V
D
(V
S
) for Different Temperature, V
DD
= 3.3 V
1.2
1.0
0.8
0.6
0.4
0.2
0
0.5 1.0 1.5 2.0 2.50
V
D
, V
S
(V)
ON RESISTANCE ()
–
40
°C
+25°C
+85°C
+125°C
V
DD
= 2.5V
04307-0-008
Figure 7. On Resistance vs. V
D
(V
S
) for Different Temperature, V
DD
= 2.5 V
V
DD
= 1.8V
–
40
°C
+25°C
+85°C
+125°C
1.4
1.2
1.0
0.9
0.7
0.5
0
ON RESISTANCE ()
0.2
0.2 0.4 0.6 0.8 1.00
V
D
, V
S
(V)
1.2
1.4
1.6
1.8
04307-0-009
Figure 8. On Resistance vs. V
D
(V
S
) for Different Temperature, V
DD
= 1.8 V
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P17

ADG804YRM

Mfr. #:
Buy ADG804YRM
Manufacturer:
Analog Devices Inc.
Description:
Multiplexer Switch ICs 4:1 33MHz 500 mOhm CMOS
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet