OMO ElectronicOMO Electronic
Expand menu
0 Cart

AFCT-5805DZ

P1-P3P4-P6P7-P9P10-P10
7
Table 1. Regulatory Compliance - Typical Performance
Feature Test Method Performance
Electrostatic
Discharge (ESD) to
the Electrical Pins
MII-STD-883F
Method 3015.7
Class 1 (>500 V) - Human Body Model
Electrostatic
Discharge (ESD)
to the Duplex SC
Receptacle
Variation of
IEC 61000-4-2
Air discharge 15 kV
Electromagnetic
Interference (EMI)
FCC Class B Typically provide greater than 11 dB margin below 1
GHz to FCC Class B when tested in a GTEM with the
transceiver mounted to a circuit card without a chassis
enclosure at frequencies up to 1 GHz. Margins above 1
GHz dependent on customer board and chassis designs.
Immunity Variation of IEC 801-3 Typically show no measurable eect from a 10 V/m eld
swept from 27 MHz to 1 GHz applied to the transceiver
without a chassis enclosure.
Eye Safety FDA CDRH 21-CFR 1040 Class 1 Accession Number: 9521220-121
IEC 60825 - 1 TUV Approved
Component
Recognition
Underwriters Laboratories and Canadian
Standards Association Joint Component
Recognition for Information Technology
Equipment Including Electrical
UL File#: E173874
Performance Specications
Absolute Maximum Ratings
Stresses in excess of the absolute maximum ratings can cause catastrophic damage to the device. Limits apply to
each parameter in isolation, all other parameters having values within the recommended operating conditions. It
should not be assumed that limiting values of more than one parameter can be applied to the product at the same
time. Exposure to the absolute maximum ratings for extended periods can adversely aect device reliability.
Parameter Symbol Minimum Maximum Units Notes
Storage Temperature T
S
-40 +85 °C
Lead Soldering Temperature/Time - - +260/10 °C/s
Input Voltage - GND V
CC
V
Power Supply Voltage - 0 6 V
Operating Environment
Parameter Symbol Minimum Maximum Units Notes
Power Supply Voltage V
CC
+3.1 +5.25 V
Ambient Operating Temperature
- AFCT-5805AZ/CZ/AMZ
T
OP
-40 +85 °C 1
Ambient Operating Temperature
- AFCT-5805BZ/DZ
T
OP
0 +70 °C 1
8
Transmitter Section
(Ambient Operating Temperature, V
CC
= 3.1 V to 5.25 V)
Parameter Symbol Minimum Typical Maximum Units Notes
Output Center Wavelength lce 1261 - 1360
Output Spectral Width (RMS) Dl - - 7.7 nm
Average Optical Output Power P
O
-15 - -8 dBm 2
Extinction Ratio E
R
8.2 - - dB
Power Supply Current I
CC
- 50 140 mA 3
Output Eye Compliant with Telcordia TR-NWT-000253 and ITU recommendation G.957
Optical Rise Time t
R
- - 2 ns 4
Optical Fall Time t
F
- - 2 ns 4
Data Input Current - Low I
IL
-350 - - µA
Data Input Current - High I
IH
- - 350 µA
Data Input Voltage - Low V
IL
- V
CC
-2.0 - -1.475 V 5
Data Input Voltage - High V
IH
- V
CC
-1.165 - -0.74 V 5
Notes:
1. 2 m/s air ow required.
2. Output power is power coupled into a single mode ber.
3. The power supply current varies with temperature. Maximum current is specied at V
CC
= Maximum @ maximum temperature (not including
terminations) and end of life. Typical power supply current at +25°C and +3.3 V or +5.0 V supply.
4. 10% - 90% Values. Maximum t
R
, t
F
times tested against eye mask.
5. These inputs are compatible with 10 K, 10 KH and 100 K PECL outputs.
Receiver Section
(Ambient Operating Temperature, V
CC
= 3.1 V to 5.25 V)
Parameter Symbol Minimum Typical Maximum Units Notes
Receiver Sensitivity - - - -31 dBm 6
Maximum Input Power - -7 - - dBm 6
Power Supply Current I
CC
- 55 100 mA 7
Signal Detect - Deasserted - -45 - -31 dBm
Signal Detect - Hysteresis - 0.5 - 4 dB
Signal Detect Assert Time
(o to on)
AS_Max - - 100 µs
Signal Detect Deassert Time
(on to o)
ANS_Max - - 350 µs
Signal Detect Output Voltage - Low V
OL
- V
CC
-1.92 - -1.45 V 8
Signal Detect Output Voltage - High V
OH
- V
CC
-1.1 - -0.85 V 8
Data Output Voltage - Low V
OL
- V
CC
-2.0 - -1.45 V 8
Data Output Voltage - High V
OH
- V
CC
-1.1 - -0.85 V 8
Data Output Rise Time t
r
- - 2.2 ns 9
Data Output Fall Time t
f
- - 2.2 ns 9
Notes
6. Sensitivity and maximum input power levels for a 2
23
-1 PRBS with 72 ones and 72 zeros inserted. (ITU recommendation G.958).
7. The current includes capacitively coupled 50 Ohm terminations.
8. These outputs are compatible with 10 K, 10 KH and 100 K PECL outputs.
9. 20 - 80% levels.
9
Table 2. Pin Out Table
Pin Symbol Functional Description
Mounting Studs The mounting studs are provided for transceiver mechanical attachment to the circuit board. They are
embedded in the housing and are not connected to the transceiver internal circuit. They should be
soldered into plated-through holes on the printed circuit board.
1 V
EER
Receiver Signal Ground
Directly connect this pin to receiver signal ground plane.
2 RD+ Receiver Data Out
Terminate this high-speed, dierential, PECL output with standard PECL techniques at the follow-on
device input pin.
3 RD- Receiver Data Out Bar
Terminate this high-speed, dierential, PECL output with standard PECL techniques at the follow-on
device input pin.
4 SD Signal Detect
Normal input optical levels to the receiver result in a logic “1” output.
Low input optical levels to the receiver result in a fault indication shown by a logic “0” output.
Signal Detect is a single-ended, PECL output. This output will operate with 270 Ω termination resistor
to V
EE
to achieve PECL output levels.
This Signal Detect output can be used to drive a PECL input on an upstream circuit, such as, Signal
Detect input and Loss of Signal-bar input.
5 V
CCR
Receiver Power Supply
Provide +3.3 or +5.0 V dc via the recommended receiver power supply lter circuit.
Locate the power supply lter circuit as close as possible to the V
CCR
pin.
6 V
CCT
Transmitter Power Supply
Provide +3.3 or +5.0 V dc via the recommended transmitter power supply lter circuit.
Locate the power supply lter circuit as close as possible to the V
CCT
pin.
7 TD- Transmitter Data In Bar
Terminate this high-speed, dierential Transmitter Data input with standard PECL techniques at the
transmitter input pin.
8 TD+ Transmitter Data In
Terminate this high-speed, dierential Transmitter Data input with standard PECL techniques at the
transmitter input pin.
9 V
EET
Transmitter Signal Ground
Directly connect this pin to the transmitter signal ground plane.
P1-P3P4-P6P7-P9P10-P10

AFCT-5805DZ

Mfr. #:
Buy AFCT-5805DZ
Manufacturer:
Broadcom / Avago
Description:
Fiber Optic Transmitters, Receivers, Transceivers Transceiver
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet