ES1000-NO.1-C1-X-50MM Datasheet ES1000-NO.3-B8-X-65MM, ES1000-NO.2-B9-X-40MM, ES1000-NO.4-B7-X-STK | P1-P2

ES1000

Semirigid, adhesive-lined heat-shrinkable

tubing (extended temperature range)

Clear, adhesive-lined ES1000

heat-shrinkable tubing is specifically

designed for environmental sealing

and electrical insulation of wire

splices, terminations, and

components where see-through

inspection is required.

ES1000 tubing has an outer jacket of

radiation-crosslinked, semirigid

polyolefin. The jacket is mechanically

tough, providing strain relief and

abrasion protection of wire splices

and mechanically sensitive

components. The inner layer of the

tubing is a unique hot-melt adhesive,

specially formulated to seal to most

types of commercial wire insulation,

and to perform well at an extended

temperature range. The thick

adhesive forms an effective barrier

against fluids and moisture, helping to

protect the harness from the effects

of corrosion and water wicking.

Because ES1000 tubing has a high

shrink ratio, only a few sizes are

needed to cover a wide range of

splice and component diameters.

ES1000 tubing dimensions have

been engineered to provide low-

cost sealing solutions on multiple-

wire splices (up to seven wires per

side), using standard Raychem

application equipment.

Temperature rating

Full recovery temperature: 135°C

Continuous operating temperature: –40°C to 130°C

Specifications*

Type Raychem UL

ES1000 RT-1113 E85381

*When ordering, always specify latest issue.



Dimensions (millimeters/inches)

Inside diameter (including core) Recovered wall thickness**

D (min.) d (max.) W W1 W2

Expanded Recovered after Minimum Minimum Minimum

Part number as supplied heating total wall jacket wall adhesive wall

ES1000-No.1 5.72 0.225 1.27 0.050 1.20 0.047 0.64 0.025 0.56 0.022

ES1000-No.2 7.44 0.293 1.65 0.065 1.52 0.060 0.76 0.030 0.76 0.030

ES1000-No.3 10.85 0.427 2.41 0.095 1.91 0.075 0.89 0.035 1.02 0.040

ES1000-No.4 17.78 0.700 4.45 0.175 2.41 0.095 1.04 0.041 1.37 0.054

**Wall thickness will be less if tubing recovery is restricted during shrinkage.

Ordering information

Color Clear

Size selection Always order the largest size that will shrink snugly over the component being covered.

Standard packaging Cut pieces. See reverse for information on standard cut lengths.

Marking Tubing will be marked with the number size (for example, ES-1, ES-2, ES-3, or ES-4).

Ordering description Specify product name, size, color, and cut length; for example, ES1000-No.2-X-50MM (X=Clear).

W2W1

Expanded as supplied

Fully recovered

after heating

Tyco Electronics Corporation

300 Constitution Drive Faraday Road 3816 Noborito, Tama-ku Asia Pacific Headquarters

Menlo Park, CA 94025-1164 Dorcan, Swindon, SN3 5HH Kawasaki, Kanagawa 214-8533 26 Ang Mo Kio, Industrial Park 2

USA United Kingdom Japan Singapore 569507

Tel:(800) 926-2425 (US & Canada) Tel: +44 1793 528171 Tel: +81 44 900 5102 Tel: +65 4866 151

Tel:+1 (650) 361-3860 (All other countries)

Users should independently evaluate the suitability of the product for their application.

For more information about this product visit www.tycoelectronics.com

All information, including illustrations, is believed to be reliable. Users, however, should independently evaluate the suitability of each product for their application. Tyco Electronics Corporation makes

no warranties as to the accuracy or completeness of the information, and disclaims any liability regarding its use. Tyco Electronics Corporation’s only obligations are those in the Standard Terms and

Conditions of Sale for these products and in no case will Tyco Electronics Corporation be liable for any incidental, indirect, or consequential damages arising from the sale, resale, use, or misuse of the

product. Tyco Electronics Corporation’s Specifications are subject to change without notice. In addition, Tyco Electronics Corporation reserves the right to make changes in materials or processing

without notification to the Buyer which do not affect compliance with any applicable specification.

Specification values

Property Unit Requirement Method of test

Physical Dimensions mm (inches) See reverse ASTM D 2671

Longitudinal change percent 0, –10 ASTM D 2671

Tensile strength* psi (MPa) 1500 (10.3) minimum ASTM D 2671

Ultimate elongation* percent 200 minimum ASTM D 2671

Low-temperature flexibility No cracking ASTM D 2671

(–40°C/–40°F)

Heat shock No cracking of ASTM D 2671

(4 hours at 225°C/437°F) outer jacket

Heat aging No cracking See note below

(168 hours at 175°C/347°F)

Electrical Volume resistivity ohm-cm 1.0 x 10

minimum ASTM D 257

Dielectric strength volts/mil 350 minimum ASTM D 149

(jacket only)**

Chemical Water absorption percent 1.0 maximum ASTM D 570

Procedure A

Note: Consult Raychem RT-1113 for specific details about test procedures.

*Calculation based on wall thickness of jacket only.

**Adhesive liner manually removed prior to testing.

Standard cut lengths

Part number Standard cut length Cut length tolerance

ES1000-No. 1 27 mm, 50 mm, 65 mm ± 1.5 mm

1220 mm ± 25.4 mm

ES1000-No. 2 27 mm, 50 mm, 65 mm ± 1.5 mm

1220 mm ± 25.4 mm

ES1000-No. 3 27 mm, 65 mm, 75 mm ± 1.5 mm

1220 mm ± 25.4 mm

ES1000-No. 4 27 mm, 75 mm, 90 mm ± 1.5 mm

1220 mm ± 25.4 mm

Raychem is a trademark of Tyco Electronics Corporation.

P1-P2

ES1000-NO.1-C1-X-50MM

Mfr. #:

Buy ES1000-NO.1-C1-X-50MM

Manufacturer:

TE Connectivity

Description:

HEATSHK TUBING 4:1 5.7DIA X 50MM

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

ES1000-NO.1-C1-X-50MM

ES1000-NO.1-C1-X-50MM

Products related to this Datasheet