Au-clad double layer
* Agency standard: Please refer to “Ordering information”.
SPECIFICATIONS
2. Characteristics
3. Operating characteristics
Actuator
Operating force
Max. gf
SPST-NO
Wire position
Straight Right angle Left angle
Leaf lever
0.89 N ABS163844* ABS463844* ABS563844*
1.08 N ABS163854* ABS463854* ABS563854*
Mechanical life
(O.T.: Specified value)
Leaf lever Min. 5x10
5
(at 60 cpm)
Other types Min. 5x10
6
(at 60 cpm)
Electrical life at rated load
(O.T.: Max.)
AgNi alloy contact type Min. 5x10
4
(at 20 cpm)
Au-clad contact type Min. 2x10
5
(at 20 cpm)
Insulation resistance Min. 100 MΩ (at 500 V DC insulation resistance meter)
Dielectric strength
Between non-continuous terminals
Between each terminal and other exposed metal parts
Between each terminal and ground
1,000 Vrms
1,500 Vrms
1,500 Vrms
Vibration resistance (Pin plunger type) 10 to 55 Hz at single amplitude of 0.75 mm (Contact opening Max. 1 msec.)
Shock resistance (Pin plunger type) Min. 294 m/s
2
(Contact opening Max. 1 msec.)
Contact resistance (Initial)
AgNi alloy contact type
Dust protected type (IP50): Max. 50 mΩ
Immersion protected type (IP67): Max. 100 mΩ
(By voltage drop 1 A 6 to 8 V DC)
Au-clad contact type
Dust protected type (IP50): Max. 100 mΩ
Immersion protected type (IP67): Max. 150 mΩ
(By voltage drop 0.1 A 6 to 8 V DC)
Allowable operating speed (at no load) 0.1 to 500 mm/sec.
Max. operating cycle rate (at no load) 120 cpm
Ambient temperature –40°C to +85°C
Unit weight Approx. 2 g (IP50 type)
Type of actuator Operating force, Max. Release force, Min.
Pretravel, Max.
mm
Movement
differential,
Max. mm
Overtravel,
Min. mm
Operating
position,
mm
Pin plunger 0.98N 1.47N 0.15N 0.20N 0.6 0.1 0.4 8.4±0.3
Short hinge lever 0.39N 0.59N 0.034N 0.039N 2.5 0.5 0.8 8.8±0.8
Hinge lever 0.34N 0.54N 0.029N 0.034N 2.8 0.8 1.2 8.8±0.8
Long hinge lever 0.25N 0.44N 0.025N 0.029N 3.5 1.0 1.6 8.8±1.2
Simulated roller lever 0.34N 0.54N 0.029N 0.034N 2.8 0.8 1.2 11.65±0.8
Roller lever 0.39N 0.59N 0.034N 0.039N 2.5 0.5 0.8 14.5±0.8
Leaf lever 0.88N 1.08N 0.17N 0.20N 4.5 1.0 2.5 14.5±1.5
1. Contact rating
Low-level circuit rating (Au-clad contact type)
Voltage
AgNi alloy contact type
Au-clad contact type
Au-clad
triple layer
Au-clad
twin layer
Resistive load Inductive load Resistive load
125 V AC 2 A 2 A 0.1 A —
250 V AC 2 A 2 A 0.1 A —
30 V DC 2 A 2 A 0.1 A 0.1 A
125 V DC 0.4 A 0.05 A — —
Rated voltage Resistive load
6 V DC 5 mA
12 V DC 2 mA
24 V DC 1 mA
Recommended contact material chart
classified by load voltage & current
(reference)
Remarks: If the contact is being used in the constant
low-level circuit load range, the Au-clad twin
layer contact is recommended. If there is a
danger of the current being less than 0.5 A,
for instance if the contact is being turned on
and off, the Au-clad triple layer type is
recommended.
Silver-alloy
Gold-clad double layer
2A
100mA
1mA
0
DC
AC
5
5
15
30V
30
250V
Gold-clad triple layer
ABS1,4,5
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
