MPL015A2T2

MPL015A2
Rev 1, 12/2010
Freescale Semiconductor
© Freescale Semiconductor, Inc., 2010. All rights reserved.
Pressure
Miniature I
2
C Digital Barometer
The MPL015A2 is an absolute pressure sensor with digital output for low cost
applications. A miniature 5 x 3 x 1.2 mm LGA package ideally suits it for portable
electronics and space constrained applications. Low current consumptions of
5 μA during Active mode and 0.06 μA during Shutdown (Sleep) mode target
battery and other low-power applications. A wide operating temperature range
from -40°C to +105°C fits demanding environmental requirements.
MPL015A2 employs a MEMS pressure sensor with a conditioning IC to provide
accurate pressure measurement from 50 to 115 kPa. An integrated ADC provides
digitized temperature and pressure sensor outputs via an I
2
C port. Calibration
Data is stored in internal ROM. Utilizing raw sensor output, the host
microcontroller executes a compensation algorithm to render Compensated
Absolute Pressure.
The MPL015A2 pressure sensor’s small form factor, low power capability,
precision, and digital output optimize it for barometric measurement applications.
Features
Digitized pressure and temperature information together with programmed
calibration coefficients for host micro use.
Factory Calibrated
50 kPa to 115 kPa Absolute Pressure
1 kPa Accuracy
2.375 V to 5.5 V Supply
Integrated ADC
•I
2
C Interface
Monotonic Pressure and Temperature Data Outputs
Surface Mount RoHS Compliant Package
ORDERING INFORMATION
Device Name Package Options Case No.
# of Ports Pressure Type
Digital
Interface
None Single Dual Gauge Differential Absolute
MPL015A2T1
Tape & Reel 2015 I
2
C
Pin Description
PIN NAME FUNCTION
1 VDD VDD Power Supply Connection.
2 CAP External Capacitor
3 GND Ground
4 SHDN Shutdown (Sleep): Connect to GND to disable the device.
5 RST Reset: Drive line low to disable I
2
C communications.
6 NC NC: No connection.
7SDA
(1)
SDA: Serial data I/O line.
8SCL
(1)
I
2
C Serial Clock Input.
1. Use 4.7k pull-up resistors for I
2
C communication.
MPL015A2
50 to 115 kPa
MPL015A2
5.0 mm X 3.0 mm X 1.2 mm MAX
LGA PACKAGE
1
NC
SDA
VDD
CAP
SHDN
GND
RST
SCL
2
3
4
8
7
6
5
PIN CONNECTIONS
Application Examples
Barometry (portable and desk-top)
Altimeters
Weather Stations
Hard Disk-Drives (HDD)
Industrial Equipment
Health Monitoring
Air Control Systems
MPL015A2
Sensors
2 Freescale Semiconductor
Pressure
Maximum Ratings
Voltage (with respect to GND unless otherwise noted)
V
DD
.............................................................................................................................. -0.3 V to +5.5 V
SCLK, CS, D
IN
, D
OUT
................................................................................................. -0.3 V to V
DD
+0.3 V
Operating Temperature Range .................................................................................... -40°C to +105°C
Storage Temperature Range........................................................................................ -40°C to +125°C
Overpressure............................................................................................................... 1000 kPa
Operating Characteristics
(V
DD
= 2.375 V to 5.5 V, T
A
= -40°C to +105°C, unless otherwise noted. Typical values are at V+ = 3.3 V, T
A
= +25°C.
Ref Parameters Symbol Conditions Min Typ Max Units
1 Operating Supply Voltage
V
DD
2.375 3.3 5.5 V
2 Supply Current
I
DD
Shutdown (SHDN = GND) @ 25ºC 0.06 1 μA
Standby — 3.5 10 μA
Average – at one measurement per second 5 6 μA
Pressure Sensor
3 Range 50 115 kPa
4 Resolution —0.15kPa
5 Accuracy @ 25ºC ±1 kPa
6 Accuracy Change over
Temperature
±0.125 kPa/ºC
7 Power Supply Rejection Typical operating circuit at DC 0.1 kPa/V
100 mV p-p 217 Hz square wave plus 100 mV
pseudo random noise with 10 MHz bandwidth.
—0.1kPa
8 Conversion Time
(Start Pressure Convert)
tcp Time between start convert command and data
available in the Pressure register
—0.60.7ms
Temperature Sensor
9 Range -40 105 ºC
10 Conversion Time
(Start Temperature Convert)
tct Time between start convert command and data
available in the Temperature register
—0.60.7ms
11 Conversion Time
(Start Both Convert)
tcb Time between start convert command and data
available in the Pressure and Temperature
registers
—0.81 ms
12 Resolution Temperature ADC is 472 counts @ 25ºC -5.35 counts/ºC
I
2
C I/O Stages: SCL, SDA
13 SCL Clock Frequency f
SCL
400 KHz
14 Low Level Input Voltage VIL 0.3V
DD
V
15 High Level Input Voltage VIH 0.7V
DD
—— V
I
2
C Outputs: SDA
16 Data Setup Time t
SU
Setup time from command receipt to ready to
transmit
100 ns
I
2
C Addressing
MPL015A2 uses 7-bit addressing, does not acknowledge the general call address 0000000. Slave address has been set to 0x60 or 1100000.
MPL015A2
Sensors
Freescale Semiconductor 3
Pressure
Figure 1. Block Diagram
Compensation
The 10-bit compensated pressure output, Pcomp, is calculated as follows:
Pcomp = a0 + (b1 + Padc + c12*Tadc) * Padc + (b2 + Tadc) * Tadc
Where:
Padc is the 10-bit pressure output of the MPL015A2 ADC,
Tadc is the 10-bit temperature output of the MPL015A2 ADC,
a0 is the pressure offset coefficient,
b1 is the pressure sensitivity coefficient,
c12 is the coefficient for temperature sensitivity coefficient (TCS),
b2 is the 1st order temperature offset coefficient (TCO),
Ideally, Pcomp will produce a value of 0 with an input pressure of 50 kPa and will produce a full-scale value of 1023 with an input
pressure of 115 kPa.
Diff
Amp
Temp
Sensor
MUX
ADC
SCL
GND
VDD
SDA
Temperature
Pressure
Coefficient
Storage
ADDR
ADDR
ADDR
ADDR
ADDR
I
2
C
Interface
SHDN
RST
CAP
Diff
Amp
Temp
Sensor
MUX
ADC
SCL
GND
VDD
SDA
Temperature
Pressure
Coefficient
Storage
ADDR
ADDR
ADDR
ADDR
ADDR
ADDR
ADDR
ADDR
I
2
C
Interface
SHDN
RST
CAP
VDD
CAP
SHDN
SDA
RST
GND
SCL
μC
1 μF
1 μF
Microcontroller
4.7 k
4.7 k

MPL015A2T2

Mfr. #:
Manufacturer:
NXP Semiconductors
Description:
IC BAROMETER I2C DGTL MINI 8-LGA
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet