MPC8245 Hardware Specifications Addendum for the MPC8245ARXXnnnx Series, Rev. 3
Freescale Semiconductor 11
PLL Configuration
17 10111 25–33
2
100–132 200–264 4 (2) 2 (2)
18 11000 27
3
–53
5
68–132 204–396 2.5 (2) 3 (2)
19 11001 36
6
–66
1
72–132 180–330 2 (2) 2.5 (2)
1A 11010 50
9
–66
1
50–66 200–264 1 (4) 4 (2)
1B 11011
13
34
3
–66
1
68–132 204–396 2 (2) 3 (2)
1C 11100 44
6
–66
1
66–99 198–297 1.5 (2) 3 (2)
1D 11101 48
6
–66
1
72–99 180–248 1.5 (2) 2.5 (2)
1E (Rev. B) 11110
10
Not usable Off Off
1E (Rev. D) 11110 33
3
–57
5
66–114 231–399 2 (2) 3.5 (2)
1F 11111
10
Not usable Off Off
Notes:
1. Limited by maximum PCI input frequency (66 MHz).
2. Limited by maximum system memory interface operating frequency (133 MHz).
3. Limited by minimum memory VCO frequency (132 MHz).
4. Limited due to maximum memory VCO frequency (372 MHz).
5. Limited by maximum CPU operating frequency (400 MHz).
6. Limited by minimum CPU VCO frequency (360 MHz).
7. Limited by maximum CPU VCO frequency (800 MHz).
8. Limited by minimum CPU operating frequency (100 MHz).
9. Limited by minimum memory bus frequency (50 MHz).
10. In clock off mode, no clocking occurs inside the MPC8245, regardless of the PCI_SYNC_IN input.
11. Range values are shown rounded down to the nearest whole number (decimal place accuracy removed) for
clarity.
12. PLL_CFG[0:4] settings that are not listed are reserved.
13. Multiplier ratios for this PLL_CFG[0:4] setting are different from the MPC8240 and are not
backwards-compatible.
14. PCI_SYNC_IN range for this PLL_CFG[0:4] setting is different from the MPC8240 and may not be fully
backwards-compatible.
15. Bits 7–4 of register offset <0xE2> contain the PLL_CFG[0:4] setting value.
16. In PLL bypass mode, the PCI_SYNC_IN input signal clocks the internal processor directly, the peripheral
logic PLL is disabled, and the bus mode is set for 1:1 (PCI:Mem) mode operation. This mode is intended for
hardware modeling support. The AC timing specifications given in this document do not apply in the PLL
bypass mode.
17. In dual PLL bypass mode, the PCI_SYNC_IN input signal clocks the internal peripheral logic directly, the
peripheral logic PLL is disabled, and the bus mode is set for 1:1 (PCI_SYNC_IN:Mem) mode operation. In
this mode, the OSC_IN input signal clocks the internal processor directly in 1:1 (OSC_IN:CPU) mode
operation, and the processor PLL is disabled. The PCI_SYNC_IN and OSC_IN input clocks must be
externally synchronized. This mode is intended for hardware modeling support. The AC timing specifications
given in this document do not apply in the dual PLL bypass mode.
Table 18. PLL Configurations for the 400-MHz Part Offering (continued)
Ref
PLL_CFG
[0:4]
11,14,15
400-MHz Part
9
Multipliers
PCI Clock Input
(PCI_SYNC_IN)
Range
1
(MHz)
Periph
Logic/Mem
Bus Clock
Range
(MHz)
CPU Clock
Range
(MHz)
PCI-to-Mem
(Mem VCO)
Mem-to-CPU
(CPU VCO)