iMcV-DS3/E3/STS-
LineTerm
Operation Manual
ii
FCC Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B computing device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which the user will be required to correct the interference at his own expense.
Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
The use of non-shielded I/O cables may not guarantee compliance with FCC RFI limits. This digital apparatus does not exceed the Class B
limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de classe B
prescrites dans le Règlement sur le brouillage radioélectrique publié par le ministère des Communications du Canada.
Limited Lifetime Warranty
Effective for products of B&B Electronics shipped on or after May 1, 2013, B&B Electronics warrants that each such
product shall be free from defects in material and workmanship for its lifetime. This limited lifetime warranty is applicable
solely to the original user and is not transferable.
This warranty is expressly conditioned upon proper storage, installation, connection, operation and maintenance of
products in accordance with their written specifications.
Pursuant to the warranty, within the warranty period, B&B Electronics, at its option will:
1. Replace the product with a functional equivalent;
2. Repair the product; or
3. Provide a partial refund of purchase price based on a depreciated value.
Products of other manufacturers sold by B&B Electronics are not subject to any warranty or indemnity offered by B&B
Electronics, but may be subject to the warranties of the other manufacturers.
Notwithstanding the foregoing, under no circumstances shall B&B Electronics have any warranty obligations or any other
liability for: (i) any defects resulting from wear and tear, accident, improper use by the buyer or use by any third party
except in accordance with the written instructions or advice of the B&B Electronics or the manufacturer of the products,
including without limitation surge and overvoltage conditions that exceed specified ratings, (ii) any products which have
been adjusted, modified or repaired by any party other than B&B Electronics or (iii) any descriptions, illustrations, figures
as to performance, drawings and particulars of weights and dimensions contained in the B&B Electronics’ catalogs, price
lists, marketing materials or elsewhere since they are merely intended to represent a general idea of the products and do
not form part of this price quote and do not constitute a warranty of any kind, whether express or implied, as to any of the
B&B Electronics’ products.
THE REPAIR OR REPLACEMENT OF THE DEFECTIVE ITEMS IN ACCORDANCE WITH THE EXPRESS WARRANTY SET
FORTH ABOVE IS B&B ELECTRONIC’ SOLE OBLIGATION UNDER THIS WARRANTY. THE WARRANTY CONTAINED
IN THIS SECTION SHALL EXTEND TO THE ORIGINAL USER ONLY, IS IN LIEU OF ANY AND ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, AND ALL SUCH WARRANTIES AND INDEMNITIES ARE EXPRESSLY DISCLAIMED,
INCLUDING WITHOUT LIMITATION (I) THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND
OF MERCHANTABILITY AND (II) ANY WARRANTY THAT THE PRODUCTS ARE DO NOT INFRINGE OR VIOLATE THE
INTELLECTUAL PROPERTY RIGHTS OF ANY THIRD PARTY. IN NO EVENT SHALL B&B ELECTRONICS BE LIABLE FOR
LOSS OF BUSINESS, LOSS OF USE OR OF DATA INTERRUPTION OF BUSINESS, LOST PROFITS OR GOODWILL OR
OTHER SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES. B&B ELECTRONIC SHALL
DISREGARD AND NOT BE BOUND BY ANY REPRESENTATIONS, WARRANTIES OR INDEMNITIES MADE BY ANY
OTHER PERSON, INCLUDING WITHOUT LIMITATION EMPLOYEES, DISTRIBUTORS, RESELLERS OR DEALERS OF
B&B ELECTRONIC WHICH ARE INCONSISTENT WITH THE WARRANTY, SET FORTH ABOVE.
iii
Table of Contents
FCC Radio Frequency Interference Statement .................................................... ii
Limited Lifetime Warranty .................................................................................. ii
About the iMcV-DS3/E3/STS-LineTerm ............................................................... 1
Installation ......................................................................................................... 1
Configuration ..................................................................................................... 2
Managed Modules ............................................................................................. 2
DIP Switch Settings ............................................................................................ 4
LED Operation ................................................................................................... 5
Troubleshooting ............................................................................................... 11
Specifications ................................................................................................... 12
B&B Electronics Technical Support ................................................................... 13
Fiber Optic Cleaning Guidelines ....................................................................... 14
Electrostatic Discharge Precautions ................................................................... 15
Safety Certifications .......................................................................................... 16
1
About the iMcV-DS3/E3/STS-LineTerm
iMcV-DS3/E3/STS-LineTerm is an SNMP manageable module that converts standard
thin coax signals ( DS3, E3/STS, STS ) to a single-mode or multi-mode fiber signal. It
performs the standard “LineTermination” (GR-820-CORE) function of these TDM-
based line signals. This function transmits an Alarm Indication Signal (AIS) on the line
whenever a received signal is lost. Line faults can easily be isolated to one line
section and do not propagate over multiple-line sections as they do with normal line
repeaters.
Each module includes one pair of BNC connectors and one pair of ST or SC fiber
optic connectors. This module can be installed in any iMediaChassis or MediaChassis
series, but can only be managed through a SNMP manageable iMediaChassis. DS3
Line Term modules must be configured as Host and Remote. To configure a module
as a Remote, set DIP Switch #10 to ON.
In addition, it is available with single-strand fiber: iMcV-DS3/E3/STS-LineTerm
BNC/SSFX modules allow two wavelengths (1310 nm and 1550 nm) to share one
fiber strand, essentially doubling the capacity of installed fiber. The single-strand
versions as HOST and REMOTE must have opposite transmit and receive wavelengths
iMcV-DS3/E3/STS-LineTerm modules must be deployed in pairs (one at each end of a
fiber line). The data transmitted on the fiber ports can only be received and
interpreted by another iMcV-DS3/E3/STS-LineTerm unit.
Installation
iMcV-DS3/E3/STS-LineTerm modules can be installed in any iMediaChassis or
MediaChassis series, but can be managed only through the iMediaChassis. Each
module requires one slot in the chassis. To install a module, remove the blank
brackets covering the slots where the module is to be installed by removing the
screws on the outside edges of the bracket. Slide the module into the chassis card
guides, until the module is securely seated in the connector. Secure the module to
the chassis by tightening the captive screw. Save any blanks removed during
installation for future use.
NOTE
It is not recommended that the iMcV-DS3/E3/STS-LineTerm module be installed in an IE-
MediaChassis/1-DC chassis (850-33100). The power source in this chassis is not isolated and
cannot support positive referenced ground systems typically used in Telco environments. The
IE-MediaChassis/2-DC and the iMediaChassis/6-DC are suitable alternatives.
2
Configuration
Proper configuration of the iMcV-DS3/E3/STS-LineTerm is required for maximum
performance and reliability. The following sections describe the prerequisites and the
configurations available for both managed and unmanaged modules.
Requirements
The iMcV-DS3/E3/STS-LineTerm conforms to many DS3/E3/STS-based environments.
Ensure all of the relevant information about the expected installation environment is
available before configuring the module. This information includes
Distance of the coax run (450 feet Max)
Distance of the fiber run (Must match fiber transceiver selected)
Troubleshooting requirements
Managed Modules
The iMcV-DS3/E3/STS-LineTerm modules can be remotely managed when installed
in an iMediaChassis with an SNMP management module.
NOTE
Before installing the modules, they must be configured for Host/Remote via the DIP
Switches. The Master/Slave condition requires this configuration:
S1-10: ON Remote Unit Enabled (only at the REMOTE end) (Remote)
S1-10: OFF Remote Unit Disabled (only at the LOCAL end) (Host)
After the module is installed, modify the SNMP enabled features by using the iView
2
SNMP management software. In a managed chassis, the software settings take
priority over DIP Switch settings. Ensure the software settings match the desired
configuration requirements for the installation.
iView² Management Software
iView² is the B&B Electronics management software designed specifically for the B&B
Electronics “iMcV” family of modules. It features a
GUI
and gives network managers
the ability to monitor and control the manageable B&B Electronics products.
iView² is available in several versions, including WebServer version 3.0, and can also
function as a snap-in module for HP OpenView Network Node Manager and other
third party SNMP Management software.
iView
2
supports the following platforms:
Windows 2000
Windows XP
3
Windows Vista
Windows 7
In addition, there are Java versions of iView² for any Java-capable operating systems
such as Linux.
Please see the
SNMP
Management Module installation guide for software
configuration options.
Unmanaged Modules
Before installing the module in an unmanaged chassis, manually configure all of the
desired DIP Switch selectable features.
DIP Switches
The iMcV-DS3/E3/STS-LineTerm DIP Switches are located at S1 and S2 on the PCB.
The S2 DIP Switches are factory configured and must not be changed. The S1 DIP
Switches provide control over the available iMcV-DS3/E3/STS-LineTerm features.
The location of the S1 DIP Switches is displayed in the following diagram:

850-14434

Mfr. #:
Manufacturer:
B+B SmartWorx
Description:
Networking Modules iMcVDS3E3STSLineTerm BNC/FX-CWDM-SM1550SC
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union