5
Absolute Maximum Ratings Thermal Information
Supply Voltage (V+ to V-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36V
V
R
to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V+, V-
Digital and Analog Input Voltage . . . . . . . . . . . . (V+) +4V to (V-) -4V
Analog Current (S to D) Continuous . . . . . . . . . . . . . . . . . . . . 30mA
Analog Current (S to D) Peak . . . . . . . . . . . . . . . . . . . . . . . . . 80mA
Operating Conditions
Temperature Range
HI-50XX-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55
o
C to 125
o
C
HI-50XX-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
o
C to 75
o
C
HI-50XX-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40
o
C to 85
o
C
Thermal Resistance (Typical, Note 1)
JA
(
o
C/W)
JC
(
o
C/W)
CERDIP Package. . . . . . . . . . . . . . . . . 75 22
SOIC Package . . . . . . . . . . . . . . . . . . . 110 N/A
PDIP Package* . . . . . . . . . . . . . . . . . . 90 N/A
Maximum Junction Temperature
Plastic Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150
o
C
Ceramic Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175
o
C
Maximum Storage Temperature . . . . . . . . . . . . . . . -65
o
C to 150
o
C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300
o
C
(SOIC - Lead Tips Only)
*Pb-free PDIPs can be used for through hole wave solder processing
only. They are not intended for use in Reflow solder processing
applications.
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1.
JA
is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications Supplies = +15V, -15V; V
R
= 0V; V
AH
(Logic Level High) = 2.4V, V
AL
(Logic Level Low) = 0.8V, V
L
=5V,
Unless Otherwise Specified. For Test Conditions, Consult Performance Characteristics,
Unused Pins are Grounded
PARAMETER
TEST
CONDITIONS
TEMP
(
o
C)
-2 -5, -9
UNITSMIN TYP MAX MIN TYP MAX
DYNAMIC CHARACTERISTICS
Switch ON Time, t
ON
(Note 5) 25 - 370 500 - 370 500 ns
Switch OFF Time, t
OFF
(Note 5) 25 - 280 500 - 280 500 ns
Charge Injection, Q (Note 3) 25 - 5 20 - 5 - mV
OFF Isolation (Note 4) 25 75 80 - - 80 - dB
Crosstalk (Note 4) 25 -80 -88 - - -88 - dB
Input Switch Capacitance, C
S(OFF)
25 - 11 - - 11 - pF
Output Switch Capacitance, C
D(OFF)
25 - 11 - - 11 - pF
Output Switch Capacitance, C
D(ON)
25 - 22 - - 22 - pF
Digital Input Capacitance, C
A
25 - 5 - - 5 - pF
Drain To Source Capacitance, C
DS(OFF)
25 - 0.5 - - 0.5 - pF
DIGITAL INPUT CHARACTERISTICS
Input Low Threshold, V
AL
Full - - 0.8 - - 0.8 V
Input High Threshold, V
AH
Full 2.4 - - 2.4 - - V
Input Leakage Current (High or Low), I
A
Full - 0.01 1.0 - 0.01 1.0 A
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range Full -15 - +15 -15 - +15 V
ON Resistance, r
ON
HI-5042 to HI-5047 (Note 2) 25 - 50 75 - 50 75
Full - - 150 - - 150
HI-5049, HI-5051 (Note 2) 25 - 25 45 - 25 45
Full - - 50 - - 50
Channel-to-Channel Match, r
ON
HI-5042 to HI-5047 25 - 2 10 - 2 10
HI-5049, HI-5051 25 - 1 5 - 1 5
HI-5042 thru HI-5051
