Document #: 38-07265 Rev. *J Page 4 of 11
Maximum Ratings
Supply Voltage to Ground Potential................–0.5V to +7.0V
DC Input Voltage (Except Ref) ..............–0.5V to V
DD
+ 0.5V
DC Input Voltage REF ...........................................–0.5 to 7V
Storage Temperature ................................. –65°C to +150°C
Max Soldering Temperature (10 sec.) ........................ 260°C
Junction Temperature................................................. 150°C
Static Discharge Voltage
(per MIL-STD-883, Method 3015) .............................>2000V
Operating Conditions
Parameter
[5]
Description
Min Max Unit
V
DD
Supply Voltage 3.0 3.6 V
T
A
Ambient Operating Temperature, Commercial 0 70 °C
Ambient Operating Temperature, Industrial –40 85 °C
C
L
Load Capacitance, below 100 MHz — 30 pF
Load Capacitance, from 100 MHz to 140 MHz — 15 pF
C
IN
Input Capacitance
[6]
—7pF
Electrical Characteristics for CY23S08SXC-xx Commercial Temperature Devices
Parameter Description Test Conditions Min Max Unit
V
IL
Input LOW Voltage — 0.8 V
V
IH
Input HIGH Voltage 2.0 — V
I
IL
Input LOW Current V
IN
= 0V — 50.0 μA
I
IH
Input HIGH Current V
IN
= V
DD
— 100.0 μA
V
OL
Output LOW Voltage
[7]
I
OL
= 8 mA (–1, –2, –4)
I
OL
= 12 mA (-1H, -2H)
—0.4 V
V
OH
Output HIGH Voltage
[7]
I
OH
= –8 mA (–1, –2, –4)
I
OH
= –12 mA (–1H, –2H)
2.4 — V
I
DD
(PD mode) Power down Supply Current REF = 0 MHz — 12.0 μA
I
DD
Supply Current Unloaded outputs, 100 MHz REF, Select
inputs at V
DD
or GND
—45.0mA
— 70.0
(–1H, –2H)
mA
Unloaded outputs, 66 MHz REF
(–1,–2,–4)
—32.0mA
Unloaded outputs, 33 MHz REF
(–1,–2,–4)
—18.0mA
Switching Characteristics for CY23S08SXC-xx Commercial Temperature Devices
Parameter
[8]
Name Test Conditions Min Typ Max Unit
t1 Output Frequency 30 pF load, –1, –1H, –2 devices 10 — 100 MHz
t1 Output Frequency 30 pF load, –4 devices 15 — 100 MHz
t1 Output Frequency 20 pF load, –1H device 10 — 133.3 MHz
t1 Output Frequency 15 pF load, –1, –2 devices 10 — 140.0 MHz
t1 Output Frequency 15 pF load, –4 devices 15 — 140.0 MHz
Duty Cycle
[7]
= t
2
÷ t
1
(–1,–2,–4,–1H, -2H)
Measured at V
DD
/2, F
OUT
= 66.66 MHz
30-pF load
40.0 50.0 60.0 %
Duty Cycle
[7]
= t
2
÷ t
1
(–1,–2,–4,–1H, -2H)
Measured at V
DD
/2, F
OUT
<66.66 MHz
15 pF load
45.0 50.0 55.0 %
Notes
5. Multiple Supplies: The voltage on any input or IO pin cannot exceed the power pin during power up. Power supply sequencing is NOT required.
6. Applies to both Ref Clock and FBK.
7. Parameter is guaranteed by design and characterization. Not 100% tested in production.
8. All parameters are specified with loaded outputs.
[+] Feedback