V103A
V103A Datasheet 1 11/18/05 Revision 3.2
Integrated Circuit Systems • 525 Race Street, San Jose, CA 95126 • tel (408) 297-1201 • www.icst.com
TRIPLE 10-BIT LVDS TRANSMITTER FOR VIDEO
General Description
The V103A LVDS display interface transmitter is
primarily designed to support pixel data transmission
between a video processing engine and a digital video
display. The data rate supports up to SXGA+
resolutions and can be used in Plasma, Rear Projector,
Front Projector, CRT and LCD display applications. It
can also be used in other high-bandwidth parallel data
applications and provides a low EMI interconnect over
a low cost, low bus width cable up to several meters in
length.
The V103A converts 35 bits of CMOS/TTL data,
clocked on the rising or falling edge of an input clock
(selectable), into six LVDS (Low Voltage Differential
Signaling) serial data stream pairs. In video
applications the 35 bits is normally divided into 10 bits
for each R, G and B channel and 5 control bits.
When combined with the V104 LVDS display interface
receiver, the V103A + V104 combination provides a
35-bit wide, 90 MHz transport. The rate of each LVDS
channel is 630 Mbps for a 90MHz data input clock, 945
Mbps for 135MHz.
Features
Pin compatible with THine THC63LVD103
Wide pixel clock range: 8 - 135 MHz
Guaranteed operation over -20 to +85° C ambient
temperature
Supports a wide range of video and graphics modes
including VGA, SVGA, XGA, SXGA, SXGA+, NTSC,
PAL, SDTV, and HDTV up to 1080I or 720P
Internal PLL requires no external loop filter
Selectable rising or falling clock edge for data
alignment
Compatible with Spread Spectrum clock source
Reduced LVDS output voltage swing mode
(selectable) to minimize EMI
CMOS/TTL data inputs can be configured for
reduced input voltage swing
Single 3.3 V supply
Low power consumption CMOS design
Power down mode
64-pin TQFP lead free package
Block Diagram
TA+
Parallel
to Serial
TA0-6
TA-
TB+
TB-
TC+
TC-
TD+
TD-
TE+
TE-
PLL
TB0-6
TC0-6
TE0-6
CLKIN
(8 to 135 MHz)
/PWDN
TD0-6
RS
R/F
7
7
7
7
7
TCLK+
TCLK-
TRIPLE 10-BIT LVDS TRANSMITTER FOR VIDEO
V103A
V103A Datasheet 2 11/18/05 Revision 3.2
Integrated Circuit Systems • 525 Race Street, San Jose, CA 95126 • tel (408) 297-1201 • www.icst.com
Pin Assignment
12
1
11
2
10
TD5
3
9
GND
4
5
6
7
8
16
15
14
13
64-pin TQFP
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
TD6
TE0
TE2
VCC
TE3
TE1
TE4
GND
TE5
CLKIN
/PWDN
PLLGND
PLLVCC
TE6
TA0
TA2
TA1
TA3
RS
TB2
TA4
TA5
GND
TA6
TB0
TB1
TB3
TB4
GND
TB5
17
18
19
20
21
22
23
24
25
26
27
28
LVDSGND
TE+
TE-
TD+
TD-
TCLK+
TCLK-
TC+
TC-
LVDSVCC
TB+
LVDSGND
32
31
30
29
LVDSGND
TA-
TB-
TA+
49
50
51
52
53
54
55
56
TB6
TC0
VCC
TC1
TC2
TC3
TC4
GND
57
58
59
60
61
62
63
64
TC5
TC6
TD0
R/F
TD1
TD2
TD3
TD4
TRIPLE 10-BIT LVDS TRANSMITTER FOR VIDEO
V103A
V103A Datasheet 3 11/18/05 Revision 3.2
Integrated Circuit Systems • 525 Race Street, San Jose, CA 95126 • tel (408) 297-1201 • www.icst.com
Pin Descriptions
RS Input Voltage Configuration to set LVDS Output Swing and Data Input Swing
Note 1: Refer to DC Electrical Characteristics.
Pin
Number
Pin
Name
Pin Type Pin Description
30, 31 TA+, TA-
LVDS OUT LVDS Serial Data Output Pairs
28, 29 TB+, TB-
24, 25 TC+, TC-
20, 21 TD+, TD-
18, 19 TE+, TE-
22, 23 TCLK+, TCLK- LVDS OUT LVDS Reference Clock Output Pair
33, 34, 35, 36,
37, 38, 40
TA0 ~ TA6
IN CMOS/TTL (or small signal) Data Bit Inputs
41, 42, 44, 45,
46, 48, 49
TB0 ~ TB6
50, 52, 53, 54,
55, 57, 58
TC0 ~ TC6
59, 61, 62, 63,
64, 1, 3
TD0 ~ TD6
4, 5, 6, 8, 9, 11,
16
TE0 ~ TE6
13 /PWDN IN High: Normal device operation
Low: Power down; all outputs become high impedance
43 RS IN Voltage level on this pin sets LVDS output swing voltage and data input
swing voltage; refer to the table at the bottom of this page.
60 R/F IN Input Clock triggering edge select. High: Rising edge; Low: Falling edge.
51, 7 VCC Power Power supply pins for TTL inputs and digital circuitry.
12 CLKIN IN Clock Input.
2, 10, 39, 47,
56
GND Ground Ground pins for TTL inputs and digital circuitry.
27 LVDSVCC Power Power supply pins for LVDS outputs.
17, 26, 32 LVDSGND Ground Ground pins for LVDS outputs.
15 PLLVCC Power Power supply pin for PLL circuitry.
14 PLLGND Ground Ground pin for PLL circuitry.
RS Input Voltage LVDS Output Swing CMOS/TTL Input Configuration (Input Voltage Swing)
VCC 350 mV Standard Configuration
1
0.6 ~ 1.4 V (VREF
1
) 350 mV Small Input Swing Configuration
1
GND 200 mV Standard Configuration
1

V103AYLF

Mfr. #:
Manufacturer:
IDT
Description:
LVDS Interface IC 10-bit LVDS Transmitter
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet