5
FN6521.1
July 23, 2008
Crosstalk (Channel-to-Channel) R
L
= 50Ω, C
L
= 5pF, f = 100kHz, V
COM
= 1V
RMS
(See Figure 6)
25 -85 dB
Total Harmonic Distortion f = 20Hz to 20kHz, V
COM
= 2V
P-P
, R
L
= 600Ω 25 0.012 %
NO or NC OFF Capacitance,
C
OFF
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V (See Figure 7) 25 38 pF
COM ON Capacitance, C
COM(ON)
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V (See Figure 7) 25 102 pF
POWER SUPPLY CHARACTERISTICS
Positive Supply Current, I+ V+ = 3.6V, V
IN
= 0V or V+ 25 0.021 µA
Full 0.72 µA
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, V
INL
Full 0.5 V
Input Voltage High, V
INH
Full 1.4 V
Input Current, I
INH
, I
INL
V+ = 3.6V, V
IN
= 0V or V+ Full -0.5 0.5 µA
Electrical Specifications - 1.8V Supply Test Conditions: V+ = +1.65V to +2V, GND = 0V, V
INH
= 1.0V, V
INL
= 0.4V (Note 5),
Unless Otherwise Specified.
PARAMETER TEST CONDITIONS
TEMP
(°C)
MIN
(Notes 6, 9) TYP
MAX
(Notes 6, 9) UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
Full 0 V+ V
ON-Resistance, r
ON
V+ = 1.8V, I
COM
= 100mA, V
NO
or V
NC
= 0V to V+
(See Figure 5, Note 10)
25 0.7 0.9 Ω
Full 0.95 Ω
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
ON
V+ = 1.65V, V
NO
or V
NC
= 1.0V, R
L
=50Ω, C
L
= 35pF
(See Figure 1)
25 50 ns
Full 55 ns
Turn-OFF Time, t
OFF
V+ = 1.65V, V
NO
or V
NC
= 1.0V, R
L
=50Ω, C
L
= 35pF
(See Figure 1)
25 25 ns
Full 30 ns
Break-Before-Make Time Delay, t
D
V+ = 2.0V, V
NO
or V
NC
= 1.0V, R
L
=50Ω, C
L
= 35pF
(See Figure 3)
Full 8 ns
Charge Injection, Q C
L
= 1.0nF, V
G
= 0V, R
G
= 0Ω (See Figure 2) 25 48 pC
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, V
INL
Full 0.4 V
Input Voltage High, V
INH
Full 1.0 V
Input Current, I
INH
, I
INL
V+ = 2.0V, V
IN
= 0V or V+ Full -0.5 0.5 µA
NOTES:
5. V
IN
= input voltage to perform proper function.
6. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
7. Flatness is defined as the difference between maximum and minimum value of ON-resistance over the specified analog signal range.
8. r
ON
matching between channels is calculated by subtracting the channel with the highest max r
ON
value from the channel with lowest max r
ON
value, between NC1 and NC2, NC3 and NC4 or between NO1 and NO2, NO3 and NO4.
9. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization
and are not production tested.
10. Limits established by characterization and are not production tested.
Electrical Specifications - 3.0V Supply Test Conditions: V+ = +2.7V to +3.3V, GND = 0V, V
INH
= 1.4V, V
INL
= 0.5V (Note 5),
Unless Otherwise Specified. (Continued)
PARAMETER TEST CONDITIONS
TEMP
(°C)
MIN
(Notes 6, 9) TYP
MAX
(Notes 6, 9) UNITS
ISL84467
