55PC6273-12-9-9CS3199 Datasheet 55PC6282-16-2/4/5/6-9CS3200, 55PC6275-14-2/4/6-9CS3199, 55PC6282-12-2/4/5/6-9CS3199 | P16-P18

Page 16 of 18 SPECIFICATION 55PC, ISSUE 8

NOTE: ANY PRINTED COPY OF THIS DOCUMENT

IS AN UNCONTROLLED COPY.

5. STANDARD PACKAGING

Unless otherwise specified (see 7.1), the following shall define the standard spooling and

labeling requirements for wire and cable furnished under this specification. Standard shipping

tolerance on ordered quantity, for both wire and cable, shall be ± 10 percent.

5.1 SPOOLING REQUIREMENTS

All layers of wire and cable shall be wound on spools or reels (see 5.1.3) with sufficient

tension to prevent shifting of layers and creation of crossovers within layers.

5.1.1 Finished Wire

Finished wire lengths shall be wound on spools or reels with the ends spliced together to

provide one mechanically and electrically continuous length. Unless otherwise specified, the

minimum continuous length between splices shall be in accordance with Table 5.

TABLE 5. FINISHED WIRE LENGTHS

Wire Size Range

(AWG)

Minimum Length

30 through 10

8 and larger

100 feet (30 m)

50 feet (15 m)

(NOTE: Metric lengths specified above apply only to those orders placed in metric.)

5.1.2 Finished Cable

Finished cable lengths shall be wound on spools or reels with all ends exposed. There shall be

no more than 5 lengths per spool or reel and no length shall be less than 50 feet (15 m).

5.1.3 Spools and Reels

Spools and reels shall be of a nonreturnable type. Each spool and reel shall have an

appropriate diameter for the respective wire or cable size. In no case shall the barrel of the

spool or reel have a diameter less than 3.5 inches (89 mm). Spools and reels shall be suitably

finished to prevent corrosion under typical storage and handling conditions. Loaded plastic

spools shall not exceed 50 pounds (23 kg). Loaded wooden reels shall have no weight

restriction.

5.1.4 Containers

Unless otherwise specified (see 7.1), finished wire and cable shall be delivered in standard

commercial containers so constructed as to ensure acceptance by common or other carrier for

safe transportation at the lowest rate to the point of delivery.

SPECIFICATION 55PC, ISSUE 8 Page 17 of 18

NOTE: ANY PRINTED COPY OF THIS DOCUMENT

IS AN UNCONTROLLED COPY.

5.2 LABELING REQUIREMENTS

All spools and reels shall be identified with the following information:

Manufacturer's Part Number

Lot Number

Quantity in Feet (or Meters)

Name of Manufacturer

6. APPLICABLE DOCUMENTS

6.1 GOVERNMENT-FURNISHED DOCUMENTS

The following documents, of the issue in effect on date of invitation for bids or request for

proposal, form a part of this specification to the extent specified herein.

6.1.1 Department of Defense

SPECIFICATIONS

Federal

UU-T-450 Tissue, Facial

STANDARDS

Military

MIL-STD-104 Limits for Electrical Insulation Color

MIL-STD-1916 DOD Preferred Methods for Acceptance of Product

(Copies of Department of Defense documents may be obtained from the Naval Publications

and Forms Center, Standardization Documents Order Desk, Bldg. 4D, 700 Robbins Ave.,

Philadelphia, PA 19111-5094; or at http://assist.daps.dla.mil/quicksearch/.)

6.2 OTHER PUBLICATIONS

The following documents, of the issue in effect on date of invitation for bids or request for

proposal, form a part of this specification to the extent specified herein.

6.2.1 American Society for Testing and Materials (ASTM)

B 193 Standard Test Method for Resistivity of Electrical Conductor Materials

D 3032 Standard Test Methods for Hookup Wire Insulation

(Copies of ASTM documents may be obtained from the American Society for Testing and

Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959; or at

www.astm.org.)

Page 18 of 18 SPECIFICATION 55PC, ISSUE 8

NOTE: ANY PRINTED COPY OF THIS DOCUMENT

IS AN UNCONTROLLED COPY.

6.2.2 International Organization for Standardization (ISO)

8402 Quality Management and Quality Assurance - Vocabulary

(Copies of ISO documents may be obtained from the International Organization for

Standardization; or at www.iso.org.)

6.2.3 National Electrical Manufacturers Association (NEMA)

WC 27500 Standard for Aerospace and Industrial Electrical Cable

(Copies of NEMA documents may be obtained from the National Electrical Manufacturers

Association, 1300 North 17th Street, Rosslyn, VA 22209; or at www.nema.org.)

6.2.4 Society of Automotive Engineers (SAE)

AS22759 Wire, Electrical, Fluoropolymer-Insulated, Copper or Copper Alloy

(Copies of SAE documents may be obtained from the Society of Automotive Engineers,

400 Commonwealth Drive, Warrendale, PA 15096-0001; or at www.sae.org.)

7. NOTES

7.1 ORDERING DATA

Procurement documents should specify the following:

a. Title, number, and revision of this specification

b. Applicable SCD part number and color code (see 1.3)

c. Quantity

d. Special preparation for delivery requirements, if applicable (see Section 5)

7.2 METRIC UNITS

Metric units (where shown in parentheses) are for information only.

7.3 TRADEMARKS

Raychem, TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks.

P1-P3 P4-P6 P7-P9 P10-P12 P13-P15 P16-P18

55PC6273-12-9-9CS3199

Mfr. #:

Buy 55PC6273-12-9-9CS3199

Manufacturer:

Raychem / TE Connectivity

Description:

Hook-up Wire 55PC627312-9-9CS3199 PRICE PER FOOT

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

55PC6273-12-9-9CS3199

55PC6273-12-9-9CS3199

Products related to this Datasheet