NOTES: (UNLESS OTHERWISE SPECIFIED)
1. ALL DIMENSIONS ARE IN INCHES [mm].
2. DIMENSIONS APPLY AFTER FINISHING.
3. MANUFACTURE TO BE COMPLIANT WITH EU RoHS DIRECTIVE.
4. SAFETY BREAK ALL SHARP CORNERS AND EDGES .02 MAXIMUM.
SHEET 1 OF 1
LDCFDLT_A
SCALE: 2:1
TITLE:
SIZE
DWG. NO.
REV
DO NOT SCALE DRAWING
ANGLES:
1
TOLERANCES:
.020 [0.50]-.200 [5.00]=
.008 [0.20]
.200 [5.00]-1.200 [30.00]=
.016 [0.40]
1.20 [30.0]-4.75 [120.0]=
.024 [0.60]
4.75 [120.0]-12.40 [315.0]=
.040 [1.0]
DRAWN:
ENGR:
DT:
DT:
MATERIAL:
FINISH:
PROJECTION:
:
THIS DRAWING CONTAINS PROPRIETARY INFORMATION
THAT IS THE SOLE PROPERTY OF LINX TECHNOLOGIES, AND SHALL BE
TREATED AS SUCH. NO DISCLOSURE OR REPRODUCTION OF THIS
DOCUMENT IS PERMITTED, IN WHOLE OR IN PART, WITHOUT THE
EXPRESS WRITTEN PERMISSION OF LINX TECHNOLOGIES OR ITS
DESIGNATED AGENTS.
159 ORT LANE
MERLIN, OR 97532
B
MCX FEMALE BULKHEAD MOUNT
CABLE END CRIMP FOR RG178 CABLE
CONMCX005-R178
11-JUL-12
B.MURPHY
S.HOGAN
11-JUL-12
REVISIONS
REV
DESCRIPTION
DATE
APPV
B
Added new title block and heat shrink; Updated instructions 11-JUL-12 SAH
Descripon Material Finish
Body
Socket
Insulaon
Gold
N/A
Gold
PTFE
Nut
Washer
Gold
Gold
Brass
Brass
Heat Shrink BlackPolyolefin
Brass
BE CU
Ø0.106
(2.70)
0.272
(6.90)
10-56 UNS-2A
THREADS
H0.250
(6.35)
0.378
(9.60)
0.571
(14.50)
FLAT 0.173
(4.40)
SIDE VIEW
0.197
(5.00)
0.024
(0.60)
RECOMMENDED CABLE STRIPPING DIMENSIONS
0.138
(3.50)
RG-178 Cable
FLAT 0.173
(4.40)
RECOMMENDED MOUNTING
HOLE
Ø0.187
(4.75)
SUPPORT
SPACER
0.055
(1.40)
10-56 UNS-2B
THREADS
H0.250
(6.35)
0.020
(0.50)
NUT
WASHER
CONREVMCX005-R178 ASSEMBLY INSTRUCTIONS
1. Strip the cable to the recommended dimensions.
Slip heat shrink onto the stripped cable.2.
Solder the support onto the braid.3.
Place the spacer onto the center conductor.4.
Solder or crimp the socket onto the center conductor.5.
6.
Insert the socket, center conductor, spacer, and support into
the body until the socket snaps in.
7.
8.
9.
Crimp the tail of the body onto the support with a 0.093”
hex crimp tool (or one labeled for use with RG-178 cable).
Use heat shrink to cover crimp.
Use the nut and washer to secure the connector to a case.
Ø0.118
(3.00)
0.787
(20.00)
HEAT SHRINK
Ø0.377
(9.57)
Support
Spacer
Gold
N/A
Brass
PTFE
Ø0.037
(0.95)
0.244
(6.20)
PIN CHUCK
0.2x2x2 GROOVE
SOCKET
