TNPV1206330KBEEN

TNPV e3
www.vishay.com
Vishay Draloric
Revision: 24-Apr-15
7
Document Number: 28881
For technical questions, contact: thinfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Note
(1)
The quoted IEC standards are also released as EN standards with the same number and identical contents.
4.38 -
Electrostatic
discharge (Human
Body Model)
IEC 61340-3-1
(1)
;
3 pos. + 3 neg. discharges
TNPV1206e3: 6 kV
TNPV1210e3: 8 kV
± (0.5 % R)
4.17.2 58 (Td) Solderability
Solder bath method;
SnPb40; non-activated flux
(215 ± 3) °C; (3 ± 0.3) s
Good tinning ( 95 % covered);
no visible damage
Solder bath method;
SnAg3Cu0.5 or SnAg3.5;
non-activated flux
(235 ± 3) °C; (2 ± 0.2) s
4.18.2 58 (Td)
Resistance to
soldering heat
Solder bath method;
(260 ± 5) °C; (10 ± 1) s
± (0.02 % R)
Reflow method 2
(IR/forced gas convection);
(260 ± 5) °C; (10 ± 1) s
4.29 45 (XA)
Component
solvent resistance
Isopropyl alcohol; 50 °C;
method 2
No visible damage
4.30 45 (XA)
Solvent
resistance
of marking
Isopropyl alcohol;
50 °C;
method 1, toothbrush
No visible damage
4.32 21 (Ue
3
)
Shear
(adhesion)
45 N No visible damage
4.33 21 (Ue
1
)
Substrate
bending
Depth 2 mm, 3 times
± (0.05 % R)
no visible damage, no open circuit in bent position
4.35 - Flammability
IEC 60695-11-5
(1)
,
needle flame test; 10 s
No burning after 30 s
4.37 67 (Cy)
Damp heat,
steady state,
accelerated
(85 ± 2) °C;
(85 ± 5) % RH;
U = 0.3 x U
max.
;
1000 h
± (0.25 % R)
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1
CLAUSE
IEC 60068-2
(1)
TEST
METHOD
TEST PROCEDURE
REQUIREMENTS PERMISSIBLE CHANGE
(R)
Stability for product type:
TNPV1206 e3
TNPV1210 e3
TNPV e3
www.vishay.com
Vishay Draloric
Revision: 24-Apr-15
8
Document Number: 28881
For technical questions, contact: thinfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DIMENSIONS
SOLDER PAD DIMENSIONS
Note
Utilization of the full specified operating voltage may require special considerations on the creepage and clearance distance between
conductors at different potential levels.
DIMENSIONS AND MASS
TYPE
H
(mm)
L
(mm)
W
(mm)
T
t
/T
b
(mm)
MASS
(mg)
TNPV1206 e3 0.55 ± 0.10 3.2 ± 0.15 1.6 ± 0.15 0.5 ± 0.25 10
TNPV1210 e3 0.60 ± 0.15 3.2 ± 0.15 2.45 ± 0.15 0.5 ± 0.25 16
RECOMMENDED SOLDER PAD DIMENSIONS
TYPE
REFLOW SOLDERING WAVE SOLDERING
Y
(mm)
X
(mm)
G
(mm)
Y
(mm)
X
(mm)
G
(mm)
TNPV1206 e3 0.9 1.7 2.0 1.1 1.7 2.3
TNPV1210 e3 0.9 2.5 2.0 1.1 2.5 2.3
H
T
t
L
W
T
b
G X
Y
Legal Disclaimer Notice
www.vishay.com
Vishay
Revision: 08-Feb-17
1
Document Number: 91000
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED

TNPV1206330KBEEN

Mfr. #:
Manufacturer:
Vishay / Dale
Description:
Thin Film Resistors - SMD 330Kohms .1% 25ppm High Voltage
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union