TCS3200, TCS3210
PROGRAMMABLE
COLOR LIGHT-TO-FREQUENCY CONVERTER
TAOS099 − JULY 2009
3
The LUMENOLOGY r Company
r
r
Copyright E 2009, TAOS Inc.
www.taosinc.com
Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted)
†
Supply voltage, V
DD
(see Note 1) 6 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage range, all inputs, V
I
−0.3 V to V
DD
+ 0.3 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating free-air temperature range, T
A
(see Note 2) −40°C to 85°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range (see Note 2) −40°C to 85°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Solder conditions in accordance with JEDEC J−STD−020A, maximum temperature (see Note 3) 260°C. . .
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values are with respect to GND.
2. Long-term storage or operation above 70°C could cause package yellowing that will lower the sensitivity to wavelengths < 500nm.
3. The device may be hand soldered provided that heat is applied only to the solder pad and no contact is made between the tip of
the solder iron and the device lead. The maximum time heat should be applied to the device is 5 seconds.
Recommended Operating Conditions
MIN NOM MAX UNIT
Supply voltage, V
DD
2.7 5 5.5 V
High-level input voltage, V
IH
V
DD
= 2.7 V to 5.5 V 2 V
DD
V
Low-level input voltage, V
IL
V
DD
= 2.7 V to 5.5 V 0 0.8 V
Operating free-air temperature range, T
A
−40 70 °C
Electrical Characteristics at T
A
= 25°C, V
DD
= 5 V (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
V
OH
High-level output voltage I
OH
= −2 mA 4 4.5 V
V
OL
Low-level output voltage I
OL
= 2 mA 0.25 0.40 V
I
IH
High-level input current 5 μA
I
IL
Low-level input current 5 μA
Power-on mode 1.4 2 mA
I
DD
Supply current
Power-down mode 0.1 μA
S0 = H, S1 = H 500 600 kHz
Full-scale frequency (See Note 4)
S0 = H, S1 = L 100 120 kHz
S0 = L, S1 = H 10 12 kHz
Temperature coefficient of responsivity λ ≤ 700 nm, −25°C ≤ T
A
≤ 70°C ± 200 ppm/°C
k
SVS
Supply voltage sensitivity V
DD
= 5 V ±10% ±0.5 %/ V
NOTE 4: Full-scale frequency is the maximum operating frequency of the device without saturation.