OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

ADCLK907/PCBZ

P1-P3P4-P6P7-P8
Evaluation Board User Guide
UG-006
One Technology Way • P. O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Te l: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Setting Up the Evaluation Board for the ADCLK905/ADCLK907/ADCLK925
Please see the last page for an important warning and disclaimers. Rev. 0 | Page 1 of 8
PACKAGE LIST
Evaluation board with component installed
Applicable documents (schematic, layout, and so on)
GENERAL DESCRIPTION
This user guide describes how to set up and use the evaluation
board for the ADCLK905/ADCLK907/ADCLK925. The same
printed circuit board (PCB) is used to evaluate all three devices.
The ADCLK905/ADCLK907/ADCLK925 data sheet should be
used in conjunction with this user guide.
The data sheet contains full technical details about the spec-
ifications and operation of these devices.
The ADCLK905/ADCLK907/ADCLK925 clock buffers are
very fast, making it important to use adequate high bandwidth
instruments to evaluate them. To that end, the evaluation board
is fabricated using a high quality dielectric material between
layers to maintain high signal integrity. Transmission line paths
are kept as close to 50 Ω as possible.
DIGITAL PICTURE OF THE EVALUATION BOARD
08182-001
Figure 1. ADCLK905/ADCLK907/ADCLK925 Evaluation Board
UG-006 Evaluation Board User Guide
Rev. 0 | Page 2 of 8
TABLE OF CONTENTS
Package List ....................................................................................... 1
General Description ......................................................................... 1
Digital Picture of the Evaluation Board ........................................ 1
Revision History ............................................................................... 2
Recommended Board Setup ........................................................3
Clock Input Configuration ..........................................................4
Evaluation Board Schematics and Artwork ...............................5
ESD Caution...................................................................................7
REVISION HISTORY
9/09—Revision 0: Initial Version
Evaluation Board User Guide UG-006
Rev. 0 | Page 3 of 8
RECOMMENDED BOARD SETUP
The recommended setup for the evaluation board is shown
in Figure 2. Note that there is no LVPECL output termination
on the evaluation board. LVPECL termination is accomplished
via the 50 Ω input of the oscilloscope. To meet the standard
LVPECL output termination (V
CC
− 2 V into 50 Ω), V
CC
is set
to 2 V and V
EE
is set to −1.3 V. This also meets the requirement
for V
CC
− V
EE
= 3.3 V.
Table 1. Basic Equipment Required
Quantity Description
1 Dual power supply
1 Signal source
1 High bandwidth oscilloscope
4 Matched high speed cables
CLOCK
SOURCE
ADCLK9xx
EVALUATION
BOARD
DUAL
POWER SUPPLY
OSCILLOSCOPE
50Ω
50Ω
+2.0V COM –1.3V
V
CC
Dx
Dx
Qx
Qx
GND V
EE
V
REF
xV
T
x
OPTIONAL AC OR
DC COUPLING
NOTES
1. FOR DC-COUPLED INPUTS, DISCONNECT V
REF
x AND V
T
x.
2. FOR AC-COUPLED INPUTS, CONNECT V
REF
x AND V
T
x.
08182-002
Figure 2. Recommended Setup for Device Evaluation
P1-P3P4-P6P7-P8

ADCLK907/PCBZ

Mfr. #:
Buy ADCLK907/PCBZ
Manufacturer:
Analog Devices Inc.
Description:
ADCLK907 Clock Buffer and Driver Evaluation Board
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet