OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

MOC3023M

P1-P3P4-P6P7-P9P10-P12P13-P15
MOC3010M, MOC3011M, MOC3012M, MOC3020M, MOC3021M, MOC3022M, MOC3023M
www.onsemi.com
4
ELECTRICAL CHARACTERISTICS
T
A
= 25°C unless otherwise specified
INDIVIDUAL COMPONENT CHARACTERISTICS
Symbol Parameters Test Conditions Device Min. Typ. Max. Unit
Emitter
V
F
Input Forward Voltage I
F
= 10 mA All 1.15 1.50 V
I
R
Reverse Leakage Current V
R
= 3 V, T
A
= 25°C All 0.01 100
mA
Detector
I
DRM
Peak Blocking Current, Either Direction
Rated V
DRM
, I
F
= 0
(1)
All 10 100 nA
V
TM
Peak On−State Voltage, Either Direction
I
TM
= 100 mA peak, I
F
= 0 All 1.8 3.0 V
1. Test voltage must be applied within dv/dt rating.
TRANSFER CHARACTERISTICS
Symbol DC Characteristics Test Conditions Device Min. Typ. Max. Unit
I
FT
LED Trigger Current Voltage = 3 V
(2)
MOC3020M 30
mA
MOC3010M
15
MOC3021M
MOC3011M
10
MOC3022M
MOC3012M
5
MOC3023M
I
H
Holding Current, Either Direction
All 100
mA
2. All devices are guaranteed to trigger at an I
F
value less than or equal to max I
FT
. Therefore, recommended operating I
F
lies between max
I
FT
(30 mA for MOC3020M, 15 mA for MOC3010M and MOC3021M, 10 mA for MOC3011M and MOC3022M, 5 mA for MOC3012M and
MOC3023M) and absolute maximum I
F
(60 mA).
ISOLATION CHARACTERISTICS
Symbol Parameters Test Conditions Device Min. Typ. Max. Unit
V
ISO
Isolation Voltage
(3)
t = 1 Minute All
4170
VAC
RMS
3. Isolation voltage, V
ISO
, is an internal device dielectric breakdown rating. For this test, pins 1 and 2 are common, and pins 4, 5 and 6 are
common.
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
MOC3010M, MOC3011M, MOC3012M, MOC3020M, MOC3021M, MOC3022M, MOC3023M
www.onsemi.com
5
TYPICAL PERFORMANCE CURVES
Figure 2. LED Forward Voltage vs. Forward
Current
Figure 3. On−State Characteristics
Figure 4. Trigger Current vs. Ambient
Temperature
Figure 5. LED Current Required to Trigger vs.
LED Pulse Width
Figure 6. dv/dt vs. Temperature
Figure 7. Leakage Current, I
DRM
vs.
Temperature
I
F
− LED FORWARD CURRENT (mA)
1 10 100
V
F
− FORWARD VOLTAGE (V)
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
T
A
= −55
o
C
T
A
= 25
o
C
T
A
= 100
o
C
V
TM
− ON−STATE VOLTAGE (V)
−3 −2 −10123
I
TM
− ON−STATE CURRENT (mA)
−800
−600
−400
−200
0
200
400
600
800
AMBIENT TEMPERATURE − T
A
(
o
C)
−40 −20020406080100
I
TM
−TRIGGER CURRENT (NORMA
LIZED)
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
NORMALIZED TO T
A
= 25_C
PW
in
− LED TRIGGER WIDTH (
〈ms)
1 2 5 10 20 50 100
I
FT
−TRIGGER CURRENT (NORMALIZED)
0
5
10
15
20
25
NORMALIZED TO:
PW
in
≥ 100 ms
T
A
− AMBIENT TEMPERATURE (
o
C)
25 30 40 6050 70 80 90 100
STATIC dv/dt (V/
ms)
0
2
4
6
8
10
12
STATIC dv/dt
CIRCUIT IN FIGURE 8
T
A
− AMBIENT TEMPERATURE (
o
C)
−40 −20020406080100
I
DRM
− LEAKAGE CURRENT (nA)
0.1
1
10
100
1000
10000
MOC3010M, MOC3011M, MOC3012M, MOC3020M, MOC3021M, MOC3022M, MOC3023M
www.onsemi.com
6
Figure 8. Static dv/dt Test Circuit
Note:
This optoisolator should not be used to drive a lo
ad directly. It is intended to be a trigger device only.
Vdc
400 V (MOC302X)
250 V (MOC301X)
R = 10 kW
C
TEST
PROBE
PULSE
INPUT
MERCURY
WETTED
RELAY
R
TEST
DUT
252 V (MOC302X)
158 V (MOC301X)
0 VOLTS
APPLIED VOLTAGE
WAVEFORM
V
max
=
dv/dt =
0.63 V
max
=
252
RC
RC RC
400 V (MOC302X)
= 250 V (MOC301X)
(MOC302X)
=
158
RC
(MOC301X)
3. The worst−case condition for static dv/dt is established
by triggering the DUT with a normal LED input current,
then removing the current. The variable R
TEST
allows
the dv/dt to be gradually increased until the DUT
continues to trigger in response to the applied voltage
pulse, even after the LED current has been removed.
The dv/dt is then decreased until the DUT stops
triggering.
RC
is measured at this point and recorded.
X100
SCOPE
1. The mercury wetted relay provides a high speed
repeated pulse to the D.U.T.
2. 100x scope probes are used, to allow high speeds and
voltages.
t
Figure 9. Resistive Load
V
CC
R
in
1
2
3
6
5
4
120 V
60 Hz
180 W
R
L
MOC3010M
MOC3011M
MOC3012M
Figure 10. Inductive Load with Sensitive Gate Triac (I
GT
3 15 mA)
V
CC
R
in
1
2
3
6
5
4
0.1 mF
180 W
C1
2.4 kW
Z
L
MOC3010M
MOC3011M
MOC3012M
120 V
60 Hz
P1-P3P4-P6P7-P9P10-P12P13-P15

MOC3023M

Mfr. #:
Buy MOC3023M
Manufacturer:
ON Semiconductor / Fairchild
Description:
Triac & SCR Output Optocouplers DIP-6 NON-ZERO TRIAC
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet