LUW E6SG-BACA-4N7Q-1-Z

2012-08-21 16
LUW E6SG
Wegen der geplanten Streichung der LED aus der IEC 60825 erfolgt die Bewertung der Augensicherheit nach dem Standard
CIE S009/E:2002 ("photobiological safety of lamps and lamp systems")
Im Risikogruppensystem dieser CIE- Norm erfüllen die in diesem Datenblatt angegebenen LED die "low risk"- Gruppe (die die
sich im "sichtbaren" Spektralbereich auf eine Expositionsdauer von 100 s bezieht). Unter realen Umständen (für
Expositionsdauer, Augenpupille, Betrachtungsabstand) geht damit von diesen Bauelementen keinerlei Augengefährdung aus.
Grundsätzlich sollte jedoch erwähnt werden, dass intensive Lichtquellen durch ihre Blendwirkung ein hohes sekundäres
Gefahrenpotenzial besitzen. Wie nach dem Blick in andere helle Lichtquellen (z.B. Autoscheinwerfer) auch, können temporär
eingeschränktes Sehvermögen und Nachbilder je nach Situation zu Irritationen, Belästigungen, Beeinträchtigungen oder sogar
Unfällen führen.
Due to the planned cancellation of the LED from IEC 60825, the evaluation of eye safety occurs according to the standard CIE
S009/E:2002 ("photobiological safety of lamps and lamp systems").
Within the risk grouping system of this CIE standard, the LEDs specified in this data sheet fall into the "low risk" group (relating
to devices in the visible spectrum with an exposure time of 100 s). Under real circumstances (for exposure time, eye pupils,
observation distance), it is assumed that no endangerment to the eye exists from these devices.
As a matter of principle, however, it should be mentioned that intense light sources have a high secondary exposure potential
due to their blinding effect. As is also true when viewing other bright light sources (e.g. headlights), temporary reduction in visual
acuity and afterimages can occur, leading to irritation, annoyance, visual impairment, and even accidents, depending on the
situation.
Attention please!
The information describes the type of component and shall not be considered as assured characteristics.
Terms of delivery and rights to change design reserved. Due to technical requirements components may contain
dangerous substances. For information on the types in question please contact our Sales Organization.
If printed or downloaded, please find the latest version in the Internet.
Packing
Please use the recycling operators known to you. We can also help you get in touch with your nearest sales office.
By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing
material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs
incurred.
Components used in life-support devices or systems must be expressly authorized for such purpose! Critical
components may
9) page 17
only be used in life-support devices or systems
10) page 17
with the express written approval of
OSRAM OS.
Revision History: 2012-08-21
Previous Version: 2011-08-25
Page Subjects (major changes since last revision) Date of change
2, 6 new Q-Number added 2008-09-15
9 Diagram „Relative Luminous Intensity“ corrected 2010-11-12
1 product image changed 2010-11-18
all Final Datasheet created 2011-08-25
all OS-NFND-2012-004 2012-08-21
Patent List
Patent No.
US 6 066 861
US 6 277 301
US 6 245 259
US 6 576 930
LUW E6SG
2012-08-21 17
Fußnoten:
1)
Helligkeitswerte werden während eines Strompulses
einer typischen Dauer von 25 ms, mit einer internen
Reproduzierbarkeit von +/- 8 % und einer erweiterten
Messunsicherheit von +/- 11 % gemessen (gemäß
GUM mit Erweiterungsfaktor k = 3).
2)
Wegen der besonderen Prozessbedingungen bei der
Herstellung von LED können typische technische
Parameter nur aufgrund statistischer Werte
wiedergegeben werden. Diese stimmen nicht
notwendigerweise mit den Werten jedes einzelnen
Produktes überein, dessen Werte sich von typischen
Werten unterscheiden können. Falls erforderlich, z.B.
aufgrund technischer Verbesserungen, werden diese
typischen Werte ohne weitere Ankündigung geändert.
3)
Die LED kann kurzzeitig in Sperrichtung betrieben
werden.
4)
R
thJA
ergibt sich bei Montage auf PC-Board FR 4
(Padgröße 16 mm
2
je Pad)
5)
Farbkoordinaten werden während eines Strompulses
einer typischen Dauer von 25 ms, mit einer internen
Reproduzierbarkeit von +/- 0,005 und einer
erweiterten Messunsicherheit von +/- 0,01 gemessen
(gemäß GUM mit Erweiterungsfaktor k = 3).
6)
Vorwärtsspannungen werden während eines
Strompulses einer typischen Dauer von 8 ms, mit
einer internen Reproduzierbarkeit von +/- 0,05 V und
einer erweiterten Messunsicherheit von +/- 0,1 V
gemessen (gemäß GUM mit Erweiterungsfaktor k=3).
7)
Im gestrichelten Bereich der Kennlinien muss mit
erhöhten Helligkeitsunterschieden zwischen
Leuchtdioden innerhalb einer Verpackungseinheit
gerechnet werden.
8)
Maße werden wie folgt angegeben: mm (inch)
9)
Ein kritisches Bauteil ist ein Bauteil, das in
lebenserhaltenden Apparaten oder Systemen
eingesetzt wird und dessen Defekt voraussichtlich zu
einer Fehlfunktion dieses lebenserhaltenden
Apparates oder Systems führen wird oder die
Sicherheit oder Effektivität dieses Apparates oder
Systems beeinträchtigt.
10)
Lebenserhaltende Apparate oder Systeme sind für
(a) die Implantierung in den menschlichen Körper
oder
(b) für die Lebenserhaltung bestimmt.
Falls sie versagen, kann davon ausgegangen werden,
dass die Gesundheit und das Leben des Patienten in
Gefahr ist.
Published by
OSRAM Opto Semiconductors GmbH
Leibnizstrasse 4, D-93055 Regensburg
www.osram-os.com
© All Rights Reserved.
Remarks:
1)
Brightness values are measured during a current
pulse of typical 25 ms, with an internal reproducibility
of +/- 8 % and an expanded uncertainty of +/- 11 %
(acc. to GUM with a coverage factor of k = 3).
2)
Due to the special conditions of the manufacturing
processes of LED, the typical data of technical
parameters can only reflect statistical figures. These
do not necessarily correspond to the actual
parameters of each single product, which could differ
from the typical data or the typical characeristic line. If
requested, e.g. because of technical improvements,
these typ. data will be changed without any further
notice.
3)
Driving the LED in reverse direction is suitable for
short term application.
4)
R
thJA
results from mounting on PC board FR 4
(pad size 16 mm
2
per pad)
5)
Chromaticity coordinates are measured during a
current pulse of typical 25 ms, with an internal
reproducibility of +/- 0,005 and an expanded
uncertainty of +/- 0,01 (acc. to GUM with a coverage
factor of k = 3).
6)
The forward voltage is measured during a current
pulse of typical 8 ms, with an internal reproducibility of
+/- 0,05 V and an expanded uncertainty of +/- 0,1 V
(acc. to GUM with a coverage factor of k=3).
7)
In the range where the line of the graph is broken, you
must expect higher brightness differences between
single LEDs within one packing unit.
8)
Dimensions are specified as follows: mm (inch)
9)
A critical component is a component used in a
life-support device or system whose failure can
reasonably be expected to cause the failure of that
life-support device or system, or to affect its safety or
the effectiveness of that device or system.
10)
Life support devices or systems are intended
(a) to be implanted in the human body,
or
(b) to support and/or maintain and sustain human life.
If they fail, it is reasonable to assume that the health
and the life of the user may be endangered.

LUW E6SG-BACA-4N7Q-1-Z

Mfr. #:
Manufacturer:
OSRAM Opto Semiconductors
Description:
Standard LEDs - SMD Ultra White 6500K
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet