2754341

5015A Phoenix Contact GmbH & Co. Postfach 1341 32819 Blomberg Germany
4
Connection
Fig. 5: Connector pin assignment for the incoming and outgoing remote bus with information
on how to assemble the cable.
1
5
9
9
6
5
5015A005
1
5
6
9
DO
DI
/DI
/DO
DI
DO
COM
COM
/DI
/DO
1
2
3
6
7
7
6
1
2
3
20
3
8
Pin Assignment of the Male and Female Remote Bus Connector
Notes on how to assemble the cable
Outgoing remote bus
9-pos. D-SUB male connector
Incoming remote bus
9-pos. D-SUB female connector
green
yellow
pink
gray
brown
bridged
Solder
side
Solder
side
Strip the cable sheath 20 mm and bare the core ends 3 mm.
Shorten the braided screen by 12 mm.
Place the braided screen evenly around the cable sheath
Male/Female
Solder side
Clamp the shield under the cable grip
(conductive connection with the housing).
In order to reduce the installation time of an INTERBUS-S systems as much as
possible, Phoenix Contact offers pre-assembled bus cable in different lengths (see
Phoenix Contact Catalog, Part 11: INTERBUS).
5015A Phoenix Contact GmbH & Co. Postfach 1341 32819 Blomberg Germany
5
Programming Data
Table 2: The most important data for the programmer
Identification code 8 (decimal)
8 (hexadecimal)
Length code 0 (hexadecimal)
Input address area 0 bytes
Output address area 0 bytes
PCP address area 0 bytes
Register length 0 bytes
Programmable functions
Disconnection of the IB ST compact station Yes
Reset of the IB ST compact station Yes
Disconnection of the outgoing remote bus Yes
Reset of the outgoing remote bus Yes
Monitoring of the remote bus cable Yes
5015A Phoenix Contact GmbH & Co. Postfach 1341 32819 Blomberg Germany
6
Technical Data
General
Type IBS ST 24 BK-T
Identification code 08 (hex)
8 (dec)
Length code 0
Register length 0
Degree of protection IP 20
Air and creepage distances VDE 0110 part1, 01/89
Permissible operating temperature From 0 °C to 55 °C
Permissible storage temperature From -20 °C to 70 °C
Housing dimensions (w
*
d
*
h) 81 mm
*
117 mm
*
116 mm
Interfaces
INTERBUS-S
- Incoming remote bus D-SUB male connector, 9-pos.
- Outgoing remote bus D-SUB female connector, 9-pos.
- IB ST interface ST cable (is included in the scope of delivery
of the I/O modules)
Number of the connectible ST modules 8
Maximum distance to the next remote bus
module 400 m
Electrical isolation between
- incoming and outgoing remote bus Test voltage 500 V AC (50 Hz)
- incoming remote bus and
IB ST interface Test voltage 500 V AC (50 Hz)
Alarm contact
- Terminal points 6, 14, 15 (see Figure 3)
- Maximum voltage U
A
30 V AC/DC
- Maximum current 0.5 A
Reconfiguration input
- Terminal points 8 (+), 18 (-) (see Figure 4)
- Nominal voltage U
REC
24 V DC
- Permissible range -30 V to +30 V (DC)
set: 13 V to 30 V (DC)
not set: -30 V to +1 V
- Current consumption (set) 2 mA typical
Supply
Terminal points 1 (+), 9 (-) (see Figure 3)
Nominal voltage U
S
24 V (DC)
Permissible ripple 3.3 V
pp
within the permissible voltage range
Permissible voltage range 20 V to 30 V (DC)
Current consumption, primary:
- without IB ST local bus modules 150 mA typical (at 24 V)
- maximum 650 mA typical (at 24 V)
Current output, secondary (ST cable):
- maximum 800 mA (9 V)
Internal fuse IBS TR 5 , 1 A (slow-blow),
Order No.: 28 06 60 0

2754341

Mfr. #:
Manufacturer:
Phoenix Contact
Description:
Terminal Block Interface Modules 24VDC I/O DB-9X2 IN
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet