Data Sheet ADM705/ADM706/ADM707/ADM708
Rev. H | Page 5 of 12
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
RESET
ADM705/
ADM706
TOP VIEW
(Not to Scale)
1
2
3
4
5
8
7
6
00088-003
MR
PFO
WDI
WDO
V
CC
GND
PFI
Figure 3. ADM705/ADM706 PDIP/SOIC
Pin Configuration
RESET
ADM707/
ADM708
TOP VIEW
(Not to Scale)
1
2
3
4 5
8
7
6
00088-004
MR
PFO
NC
V
CC
GND
PFI
NC = NO CONNECT
RESET
Figure 4. ADM707/ADM708 PDIP/SOIC
Pin Configuration
PFO
ADM708
TOP VIEW
(Not to Scale)
1
2
3
4
5
8
7
6
00088-005
RESET
GND
PFI
NC
RESET
MR
V
CC
NC = NO CONNECT
Figure 5. ADM708 MSOP
Pin Configuration
Table 3. Pin Function Descriptions
Mnemonic
Pin Number
Description
ADM705/
ADM706
(PDIP, SOIC)
ADM707/
ADM708
(PDIP, SOIC)
ADM708
(MSOP)
MR
1 1 3
Manual Reset Input. When this pin is taken below 0.8 V, a reset is generated. MR can be
driven from TTL, CMOS logic, or from a manual reset switch as it is internally debounced.
An internal 250 μA pull-up current holds the input high when floating.
V
CC
2 2 4 5 V Power Supply Input. Place a 0.1 μF decoupling capacitor between the V
CC
and GND pins.
GND 3 3 5 0 V Ground Reference for All Signals.
PFI 4 4 6
Power Fail Input. PFI is the noninverting input to the power fail comparator. When PFI is
less than 1.25 V, PFO goes low. If unused, PFI must be connected to GND.
PFO
5 5 7
Power Fail Output. PFO is the output from the power fail comparator. It goes low when
PFI is less than 1.25 V.
WDI 6
Not
applicable
Not
applicable
Watchdog Input. WDI is a three-level input. If WDI remains either high or low for longer
than the watchdog timeout period, the watchdog output (WDO
) goes low. The timer
resets with each transition at the WDI input. Either a high to low or a low to high transition
clears the counter. The internal timer is also cleared whenever reset is asserted. The
watchdog timer is disabled when WDI is left floating or connected to a three-state buffer.
NC
Not
applicable
6 8 No Connect.
RESET
7 7 1
Logic Output. RESET
goes low for 200 ms when triggered. It can be triggered either by
V
CC
being below the reset threshold or by a low signal on the manual reset input (MR).
RESET
remains low whenever V
CC
is below the reset threshold (4.65 V in ADM705/ADM707,
4.40 V in ADM706/ADM708). It remains low for 200 ms after V
CC
goes above the reset
threshold or MR
goes from low to high. A watchdog timeout does not trigger RESET unless
WDO
is connected to MR.
WDO
8
Not
applicable
Not
applicable
Watchdog Output. WDO remains low until the watchdog timer is cleared. WDO also
goes low during low line conditions. Whenever V
CC
is below the reset threshold, WDO
goes low if the internal WDO remains low. As soon as V
CC
goes above the reset threshold,
WDO goes high.
RESET
Not
applicable
8 2
Logic Output. RESET is an active high output suitable for systems that use active high
reset logic. It is the inverse of RESET
.