B221
DF11 Series●2mm Double-Row Connector (Product Compliant to UL/CSA Standard)
■Product Specifications
Current rating
(Note 1)
Voltage rating
Crimping
Insulation Displacement
Crimping
250V AC
Insulation Displacement
100V AC
AWG
#22 to #26 :
2A
Wire size AWG #28 : 1A
AWG #30 : 0.5A
Wire size AWG #26 : 1A
Operating Temperature Range
Operating Humidity Range
Storage Temperature Range
Storage Humidity Range
■UL
·
CSA Safety Standard File No.
UL :E52653
CSA :LR95109
-30 to 85ç Note 2
40 to 80%
-10 to 60ç Note 3
40 to 70%
Note 1: Current rating of header is 2A.
Note 2: Includes temperature rise caused by current flow.
Note 3: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and
Humidity range covers non conducting condition of installed connectors in storage, shipment or during transportation.
Note 4: Information contained in this catalog represents general requirements for this Series. Contact us for the drawings and specifications for
a specific part number shown.
Item Specification Condition
1. Insulation Resistance 1000M
ohms
min. 500V DC
2. Withstanding voltage
No flashover or insulation breakdown.
650V AC/1 minute
3. Contact Resistance 30m
ohms
max. 100mA
4.
Single Insertion/Extraction Force
0.3N (30gf) min., 4.4N(450gf) max.
Measured by the square steel-made pin of 0.5±0.002mm
5. Vibration
No electrical discontinuity of 1µs or more
Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 directions.
6.
Humidity (Steady state)
Contact resistance: 30m ohms max. Insulation resistance: 500M ohms min.
96 hours at temperature of 40ç and humidity of 90% to 95%
7. Temperature Cycle
Contact resistance: 30m ohms max. Insulation resistance: 1000M ohmsmin.
(-55ç: 30 minutes ➝ 5 to 35ç: 5 to 15 minutes
(-85ç: 30 minutes ➝ 5 to 35ç: 5 to 15 minutes) 5 cycles
8.
Durability (Mating/un-mating)
Contact resistance: 30m
ohms
max.
Tin plated: 30 cycles
Gold plated:50 cycles
Flow: Manual soldering:
9.
Resistance to Soldering heat
No deformation of components affecting performance.
260ç for 10 seconds 300ç for 2 seconds
Reflow: Manual soldering:
At the recommended temperature profile
300ç for 3 seconds
■Features of DF11 Insulation Displacement Machine
(
Single Core Punching Full Automatic ID Machine AM700/DF11
)
● 5 Major Features of ID Machine AM700/DF11
1. Perform the multi-harness.
2. The setup time has been widely reduced. (10 minutes maximum)
3. Space saving design.
(About half space compared with the conventional machine)
4. Minimize initial cost with low cost.
5. The harness data can be saved in the floppy disk and easily
changed.
■Points
Since the DF11 insulation displacemention allows double rows ID with a single part, the harness service is completed with
machine connection only.
Rating
Current rating
Voltage rating
UL-CSA Safety Standard Approved Specification
30V AC
AWG #22 : 2A
Wire size AWG #
24 to #28
: 1A
AWG #30 : 0.5A
Rating
Data storage
Low cost
Multi-harness
Half space
Setup in 10 minutes
