FCBP110LD1L30S Datasheet FCBP110LD1L03, FCBP110LD1L30S, FCBP110LD1L03S | P4-P6

F i n i s a r

IV. High Speed Electrical Characteristics (T

OP

= 0 to 60°C, V

CC

= 3.3 ± 5% Volts)

Parameter – Transmitter Inputs Symbol Conditions Min Typ Max Units

Ref.

Reference Differential Input

Impedance

Z

d

100

Ω

Termination Mismatch ΔZ

M

5 % 1

Input AC Common Mode Voltage

25

mV

(RMS)

Differential Input Return Loss SDD11

0.01-1.0 GHz -12 dB

1.0 – 11.1 GHz dB 2

Differential to Common Mode

Loss

SCD11 0.01-11.1 GHz

-10 dB 3

Notes:

1. See SFF-8431 Rev 4.2 (SFP+) section D.15 Termination Mismatch for definition & test recommendations

2. Return Loss given by equation SDD11(dB)= -12.9 + 0.9·f, with f in GHz. See Figure 4

3. Common mode reference impedance is 25Ω. Differential to common mode conversion relates to generation of

EMI.

Transmitter Input Jitter Specification Symbol Min Typ Max Units Ref.

Total Jitter TJ

IN

0.38 UI 1

Data Dependent Jitter DDJ

IN

0.15 UI 1

Uncorrelated Jitter UJ

IN

0.029 UIrms 1,2

Notes:

1. Additional host margin to SFF-8431 rev 4.2. Provided to allow use of SFP+ adapters (P/N FTLX0071D4BNL).

2. Derived here by scaling the SFF-8431 rev4.2 spec of 0.023 by the relative increase in the non-data dependent

jitter over the SFF-8431 rev 4.2 spec: [(0.38-0.15) / (0.28 – 0.10)] * 0.023 UIrms.

-500

-400

-300

-200

-100

0

100

200

300

400

500

0 0.2 0.4 0.6 0.8 1

UI

Vdiff (mV)

Figure 2. Transmitter Input Differential Signal Condition Mask

F i n i s a r

Parameter – Receiver Outputs Symbol Conditions Min Typ Max Units Ref.

Reference Differential Output Impedance Z

d

100 Ω

Termination Mismatch ΔZ

M

5 % 1

Output AC Common Mode Voltage See XFP MSA E.5 15 mV

RMS

Output Rise and Fall time (20% to 80%) t

RH

, t

FH

24 ps

Differential Output Return Loss SDD22

0.01-1.0 GHz -12 dB

1.0 – 11.1 GHz dB 2

Common Mode Output Return Loss SCC22

0.01-2.5 GHz -6 dB 3

2.5-11.1 GHz -3 dB 3

Notes:

1. See SFF8431 Rev 4.2 (SFP+) section D.15 Termination Mismatch for definition and test recommendations

2. Differential Return Loss given by equation SDD22(dB)= -12.9 + 0.9·f, with f in GHz. See Figure 4

3. Common mode reference impedance is 25 Ω.

Receiver Output Jitter Specification Symbol Min Typ Max Units Ref.

Deterministic Jitter DJ

OUT

0.38 UI 1,2

Total Jitter TJ

OUT

0.64 UI 1,2

Notes:

1. When transmitter input jitter specs are met.

2. Additional host margin to SFF-8431 rev 4.2. Provided also to allow use of passive SFP+ adapters

-500

-400

-300

-200

-100

0

100

200

300

400

500

0 0.2 0.4 0.6 0.8 1

UI

Vdiff (mV)

Figure 3. Receiver Output Differential Signal Mask

F i n i s a r

-15

-10

-5

0

024681012

Freq (GHz)

SD

11,22

(dBm)

Figure 4. Maximum Transmitter Input and Receiver Output Differential Return Loss

V. General Specifications

Data Rate Specifications Symbol Min Typ Max Units Ref.

Bit Rate BR 1000 103125 Mb/sec 1

Bit Error Ratio BER 10

-12

2

Notes

:

1. 1/10 Gigabit Ethernet and 1/2/4/8G Fibre Channel compliant.

2. Tested with a PRBS 2

31

-1 test pattern.

VI. Environmental Specifications

Finisar active cables have an operating temperature range from 0°C to +60°C case temperature.

Environmental Specifications Symbol Min Typ Max Units Ref.

Case Operating Temperature T

o

p

0 60 °C

Storage Temperature T

sto

-40 85 °C

VII. Regulatory Compliance

The FCBP110LD1Lxx Laserwire, which contains laser devices, is also a Class 1 laser product

and complies with 21CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice

No. 50, dated June 24, 2007, and it complies with EN(IEC) 60825 Edition 1.2 regulations. The

FCBP110LD1Lxx Laserwire is also RoHS Compliant.

Copies of certificates are available at Finisar Corporation upon request.

FCBP110LD1L30S

FCBP110LD1L30S

Products related to this Datasheet