EVB-EN5337QI

Enpirion
®
Power Evaluation Board User Guide
EN5337QI
Enpirion EN5337QI 3A DCDC Converter w/Integrated Inductor
Evaluation Board
Introduction
Thank you for choosing Altera Enpirion power products!
The EN5337QI features integrated inductor, power MOSFETS, Controller,
a bulk of the compensation Network, and protection circuitry against
system faults. This level of integration delivers a substantial reduction in
footprint and part count over competing solutions. However, the evaluation
board is not optimized for minimum footprint; rather for engineering ease
of evaluation through programming options, clip leads, test points etc.
The EN5337QI features a customer programmable output voltage by
means of a resistor divider. The resistor divider allows the user to set the
output voltage to any value within the range 0.75V to (V
IN
-V
DROPOUT
). The
evaluation board, as shipped is populated with a 4 resistor divider option.
The upper resistor is fixed (150k) and has a phase lead capacitor (27pF)
in parallel. One of 4 lower resistors is selected with the jumper option for
output voltages of 1.0V, 1.2V, 1.55V and 2.5V. To change any of the
output voltages, retain the upper resistor and capacitor values and change
only the lower resistor.
This device has no over-voltage protection feature. We strongly
recommend the customer to ensure the feedback loop is truly closed
before powering up the device especially if the load can not withstand the
input voltage.
The input capacitor is a 10V rated 22uF X5R MLCC. The output filter
section is populated with 1 x 47uF and 1 x10uF, 6.3V rated X5R MLC
capacitors to achieve the required ~50uF of output capacitance. This
combination of output caps yields very low ESR and hence low output
ripple. A single 47uF capacitor may be substituted if minimizing footprint
is important. The Soft-start capacitor is a small 10V rated 15nF X5R
MLCC.
Pads are available to add an additional input capacitor, and there are a
total of 5 pads to accommodate the output capacitor(s). This allows for
evaluation of performance over a wide range of input/output capacitor
combinations.
1
www.altera.com/enpirion
Enpirion
®
Power Evaluation Board User Guide
EN5337QI
Clip on terminals are provided for ENA, SS, POK, VIN and VOUT. Other
test points are also made available.
A jumper is provided for controlling the Enable signal. Enable may also be
controlled using an external switching source by removing the jumper and
applying the enable signal to the middle pin and ground.
A jumper is also provided to connect a resistor load to POK pin. This
jumper is especially useful to measure the disable current and eliminates
having to subtract the current drawn by the POK resistor.
Foot print is also provided for a SMA connector to SYNC input. The SYNC
input allows the device switching to be phase locked to an external clock
signal. This external clock synchronization allows for moving any offending
beat frequency to be moved out-of-band. A swept frequency applied to this
pin results in spread spectrum operation and reduces the peaks in the
noise spectrum of emitted EMI.
Numerous test points are provided as well as banana plugs for input and
output connections. Input / Output ripple are best measured directly across
the appropriate capacitors. The switching waveform may be viewed
between test points labeled SW and GND.
The board comes with input decoupling and reverse polarity protection to
guard the device against common setup mishaps.
2
www.altera.com/enpirion
Enpirion
®
Power Evaluation Board User Guide
EN5337QI
Quick Start Guide
o f the
Figure 1 shows a top view evaluation board.
WARNING: complete steps 1 through 4 before applying power to the
EN5337QI evaluation board.
STEP 1: Set the “ENABLE jumper to the Disable Position.
Figure 2: Shows POK & Enable Jumpers
(POK jumper as shown connects pull-up resistor to VIN.
Enable jumper shown in DISABLE position.)
STEP 2: Connect Power Supply to the input power connectors, VIN (+) and
GND (-) as indicated in Figure 1 and set the supply to the desired voltage. The
device disable current may be measured in this configuration.
CAUTION: be mindful of the polarity. Even though the evaluation board
comes with reverse polarity protection diodes, it is rarely a good idea to
reverse the input polarity.
Disable
Position
3
www.altera.com/enpirion

EVB-EN5337QI

Mfr. #:
Manufacturer:
Intel / Altera
Description:
Power Management IC Development Tools Eval Board EN5337QI 3A Sync. Buck Convtr
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet