OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

EL7158IS-T7

P1-P3P4-P6P7-P9
1
®
FN7349.2
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774
| Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2003, 2004, 2007. All Rights Reserved. Elantec is a registered trademark of Elantec Semiconductor, Inc.
All other trademarks mentioned are the property of their respective owners.
EL7158
Ultra-High Current Pin Driver
The EL7158 high performance pin
driver with three-state is suited to
many ATE and level-shifting
applications. The 12A peak drive capability makes this part
an excellent choice when driving high capacitance loads.
The output pin OUT is connected to input pins VH or VL
respectively, depending on the status of the IN pin. When the
OE pin is active low, the output is placed in the three-state
mode. The isolation of the output FETs from the power
supplies enables VH and VL to be set independently,
enabling level-shifting to be implemented. Related to the
EL7155, the EL7158 adds a lower supply pin VS- and makes
VL an isolated and independent input. This feature adds
applications flexibility and improves switching response due
to the increased enhancement of the output FETs.
This pin driver has improved performance over existing pin
drivers. It is specifically designed to operate at voltages
down to 0V across the switch elements while maintaining
good speed and ON-resistance characteristics.
Available in the 8 Ld SOIC package, the EL7158 is specified
for operation over the full -40°C to +85°C temperature range.
Pinout
EL7158
(8 LD SOIC)
TOP VIEW
Features
• Clocking speeds up to 40MHz
• 12ns t
R
/t
F
at 2000pF C
LOAD
• 0.2ns rise and fall times mismatch
• 0.5ns t
ON
-t
OFF
prop delay mismatch
• 3.5pF typical input capacitance
• 12A peak drive
• Low ON-resistance of 0.5Ω
• High capacitive drive capability
• Operates from 4.5V to 12V
• Pb-free plus anneal available (RoHS compliant)
Applications
• ATE/burn-in testers
• Level shifting
•IGBT drivers
• CCD drivers
1
2
3
4
8
7
6
5
L
O
G
I
C
VS+
OE
IN
GND
VH
OUT
VL
VS-
Ordering Information
PART
NUMBER
PART
MARKING PACKAGE
TAPE &
REEL
PKG.
DWG. #
EL7158IS 7158IS 8 Ld SOIC - MDP0027
EL7158IS-T7 7158IS 8 Ld SOIC 7” MDP0027
EL7158IS-T13 7158IS 8 Ld SOIC 13” MDP0027
EL7158ISZ
(Note)
7158ISZ 8 Ld SOIC
(Pb-free)
- MDP0027
EL7158ISZ-T7
(Note)
7158ISZ 8 Ld SOIC
(Pb-free)
7” MDP0027
EL7158ISZ-T13
(Note)
7158ISZ 8 Ld SOIC
(Pb-free)
13” MDP0027
NOTE: Intersil Pb-free products employ special Pb-free material
sets; molding compounds/die attach materials and 100% matte tin
plate termination finish, which is compatible with both SnPb and
Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed
the Pb-free requirements of IPC/JEDEC J Std-020B.
Data Sheet May 14, 2007
2
FN7349.2
May 14, 2007
Absolute Maximum Ratings (T
A
= +25°C) Thermal Information
Supply Voltage (V
S
+ to V
S
-) . . . . . . . . . . . . . . . . . . . . . . . . . . .+18V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . .V
S
- -0.3V, V
S
+0.3V
Continuous Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . 500mA
Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C
Ambient operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C
Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . .+125°C
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see curves
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: T
J
= T
C
= T
A
Electrical Specifications V
S
+ = +12V, V
H
= +12V, V
L
= 0V, V
S
- = 0V, T
A
= +25°C, unless otherwise specified.
PARAMETER DESCRIPTION CONDITION MIN TYP MAX UNIT
INPUT
V
IH
Logic ‘1’ Input Voltage 2.4 V
I
IH
Logic ‘1’ Input Current V
IH
= V
S
+0.110µA
V
IL
Logic ‘0’ Input Voltage 0.8 V
I
IL
Logic ‘0’ Input Current V
IL
= 0V 0.1 10 µA
C
IN
Input Capacitance 3.5 pF
R
IN
Input Resistance 50 MΩ
OUTPUT
R
OVH
ON-Resistance V
H
to OUT I
OUT
= -500mA 0.5 1 Ω
R
OVL
ON-Resistance V
L
to OUT I
OUT
= +500mA 0.5 1 Ω
I
OUT
Output Leakage Current OE = 0V, OUT = V
H
/V
L
0.1 10 µA
I
PK
Peak Output Current
(linear resistive operation)
Source 12 A
Sink 12 A
I
DC
Continuous Output Current Source/Sink 500 mA
POWER SUPPLY
I
S
Power Supply Current Inputs = V
S
+1.33mA
I
VH
Off Leakage at V
H
and V
L
V
H
, V
L
= 0V 4 10 µA
SWITCHING CHARACTERISTICS
t
R
Rise Time C
L
= 2000pF 12.0 ns
t
F
Fall Time C
L
= 2000pF 12.2 ns
t
RFΔ
t
R
, t
F
Mismatch C
L
= 2000pF 0.2 ns
t
d-1
Turn-Off Delay Time C
L
= 2000pF 22.5 ns
t
d-2
Turn-On Delay Time C
L
= 2000pF 22.0 ns
t
dΔ
t
d-1
-t
d-2
Mismatch C
L
= 2000pF 0.5 ns
t
d-3
Three-State Delay Enable 22 ns
t
d-4
Three-State Delay Disable 22 ns
SR+ V
OUT
+ Slew Rate R
LOAD
= 6Ω 800 V/µs
SR- V
OUT
- Slew Rate R
LOAD
= 6Ω 800 V/µs
EL7158
3
FN7349.2
May 14, 2007
Electrical Specifications V
S
+ = +12V, V
H
= +1.2V, V
L
= 0V, V
S
- = 0V, T
A
= +25°C, unless otherwise specified. (Continued)
PARAMETER DESCRIPTION CONDITION MIN TYP MAX UNIT
INPUT
V
IH
Logic ‘1’ Input Voltage 2.0 V
I
IH
Logic ‘1’ Input Current V
IH
= V
S
+0.110µA
V
IL
Logic ‘0’ Input Voltage 0.8 V
I
IL
Logic ‘0’ Input Current V
IL
= 0V 0.1 10 µA
C
IN
Input Capacitance 3.5 pF
R
IN
Input Resistance 50 MΩ
OUTPUT
R
OVH
ON-Resistance V
H
to OUT I
OUT
= -500mA 0.5 1 Ω
R
OVL
ON-Resistance V
L
to OUT I
OUT
= +500mA 0.5 1 Ω
I
OUT
Output Leakage Current OE = 0V, OUT = V
H
/V
L
0.1 10 µA
I
PK
Peak Output Current
(linear resistive operation)
Source 1.2 A
Sink 1.2 A
I
DC
Continuous Output Current Source/Sink 500 mA
POWER SUPPLY
I
S
Power Supply Current Inputs = V
S
+12.5mA
V
H
Off Leakage at V
H
and V
L
V
H
, V
L
= 0V 4 10 µA
SWITCHING CHARACTERISTICS
t
R
Rise Time C
L
= 2000pF 11 ns
t
F
Fall Time C
L
= 2000pF 11 ns
t
RFΔ
t
R
, t
F
Mismatch C
L
= 2000pF 0 ns
t
d-1
Turn-Off Delay Time C
L
= 2000pF 20.5 ns
t
d-2
Turn-On Delay Time C
L
= 2000pF 20.0 ns
t
dΔ
t
d-1
-t
d-2
Mismatch C
L
= 2000pF 0.5 ns
t
d-3
Three-State Delay Enable 20 ns
t
d-4
Three-State Delay Disable 20 ns
SR+ V
OUT
+ Slew Rate R
LOAD
= 6Ω 80 V/µs
SR- V
OUT
- Slew Rate R
LOAD
= 6Ω 80 V/µs
EL7158
P1-P3P4-P6P7-P9

EL7158IS-T7

Mfr. #:
Buy EL7158IS-T7
Manufacturer:
Renesas / Intersil
Description:
IC PIN DRIVER 40MHZ 3ST 8-SOIC
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet