OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

ISL55143IRZ-T

P1-P3P4-P6P7-P9P10-P12P13-P14
10
FN6230.4
August 13, 2015
ISL55141, ISL55142, ISL55143
Package Outline Drawing
L16.4x4A
16 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE
Rev 3, 03/15
NOTES:
1. Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2. Dimensioning and tolerancing conform to ASME Y14.5m-1994.
3. Unless otherwise specified, tolerance: Decimal ± 0.05
4. Dimension applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
5. Tiebar shown (if present) is a non-functional feature.
6. The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be either
a mold or mark feature.
TOP VIEW
INDEX AREA
(4X)
0.15
PIN 1
6
4.00
4.00
A
B
SEE
TYPICAL RECOMMENDED LAND PATTERN
0.20 REF
+0.03/-0.02
DETAIL "X"
C
5
SIDE VIEW
BOTTOM VIEW
0.08 C
C
SEATING
0.10
C
+0.05
PIN #1
5
8
4
0.10 CM
12
9
4
0.50
12X
13
4X 1.50
16
1
6
A B
( 2.40)
(12x 0.50)
(16x 0.25)
(3.8 TYP)
-0.07
0.25
0.90±0.10
2.40
16x 0.40±0.01
(16x 0.60)
INDEX AREA
2.40
DETAIL "X"
PLANE
11
FN6230.4
August 13, 2015
ISL55141, ISL55142, ISL55143
Package Outline Drawing
M14.173
14 LEAD THIN SHRINK SMALL OUTLINE PACKAGE (TSSOP)
Rev 3, 10/09
DETAIL "X"
SIDE VIEW
TYPICAL RECOMMENDED LAND PATTERN
TOP VIEW
B
A
17
8
14
C
PLANE
SEATING
0.10 C
0.10 CBA
H
PIN #1
I.D. MARK
5.00 ±0.10
4.40 ±0.10
0.25 +0.05/-0.06
6.40
0.20 C B A
0.05
0°-8°
GAUGE
PLANE
SEE
0.90 +0.15/-0.10
0.60 ±0.15
0.09-0.20
5
2
31
3
1.00 REF
0.65
1.20 MAX
0.25
0.05 MIN
0.15 MAX
(1.45)
(5.65)
(0.65 TYP) (0.35 TYP)
DETAIL "X"
1. Dimension does not include mold flash, protrusions or gate burrs.
Mold flash, protrusions or gate burrs shall not exceed 0.15 per side.
2. Dimension does not include interlead flash or protrusion. Interlead
flash or protrusion shall not exceed 0.25 per side.
3. Dimensions are measured at datum plane H.
4. Dimensioning and tolerancing per ASME Y14.5M-1994.
5. Dimension does not include dambar protrusion. Allowable protrusion
shall be 0.80mm total in excess of dimension at maximum material
condition. Minimum space between protrusion and adjacent lead is 0.07mm.
6. Dimension in ( ) are for reference only.
7. Conforms to JEDEC MO-153, variation AB-1.
NOTES:
END VIEW
12
FN6230.4
August 13, 2015
ISL55141, ISL55142, ISL55143
Quad Flat No-Lead Plastic Package (QFN)
Micro Lead Frame Plastic Package (MLFP)
L20.5x5
20 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE
SYMBOL
MILLIMETERS
NOTESMIN NOMINAL MAX
A 0.80 0.90 1.00 -
A1 - 0.02 0.05 -
A2 - 0.65 1.00 9
A3 0.20 REF 9
b 0.23 0.30 0.38 5, 8
D 5.00 BSC -
D1 4.75 BSC 9
D2 2.95 3.10 3.25 7, 8
E 5.00 BSC -
E1 4.75 BSC 9
E2 2.95 3.10 3.25 7, 8
e 0.65 BSC -
k0.20 - - -
L 0.35 0.60 0.75 8
N202
Nd 5 3
Ne 5 3
P- -0.609
--129
Rev. 4 11/04
NOTES:
1. Dimensioning and tolerancing conform to ASME Y14.5-1994.
2. N is the number of terminals.
3. Nd and Ne refer to the number of terminals on each D and E.
4. All dimensions are in millimeters. Angles are in degrees.
5. Dimension b applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
6. The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
7. Dimensions D2 and E2 are for the exposed pads which provide
improved electrical and thermal performance.
8. Nominal dimensions are provided to assist with PCB Land Pattern
Design efforts, see Intersil Technical Brief TB389.
9. Features and dimensions A2, A3, D1, E1, P & are present when
Anvil singulation method is used and not present for saw
singulation.
10. Compliant to JEDEC MO-220VHHC Issue I except for the "b"
dimension.
P1-P3P4-P6P7-P9P10-P12P13-P14

ISL55143IRZ-T

Mfr. #:
Buy ISL55143IRZ-T
Manufacturer:
Renesas / Intersil
Description:
Analog Comparators W/ANNEAL QD COMPARAT 36LD 6X6 -40/+85 T
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet