24LC014H-E/MS Datasheet 24AA014HT-I/MNY, 24LC014HT-I/MNY, 24AA014H-I/ST | P1-P3

24AA014H/24LC014H

Device Selection Table

Features:

• Single-Supply with Operation down to 1.7V

• Low-Power CMOS Technology:

- 400 μA active current, maximum

-1 μA standby current, maximum (I-temp)

• Organized as a Single Block of 128 Bytes

(128 x 8)

• 2-Wire Serial Interface Bus, I

C™ Compatible

• Schmitt Trigger Inputs for Noise Suppression

• Output Slope Control to Eliminate Ground Bounce

• 100 kHz and 400 kHz Compatibility

• 1 MHz Compatibility (LC)

• Page Write Buffer for up to 16 Bytes

• Self-Timed Write Cycle (including Auto-Erase)

• Hardware Write Protection for Half Array

(40h-7Fh)

• Address Lines Allow up to Eight Devices on Bus

• 1 Million Erase/Write Cycles

• ESD Protection > 4,000V

• Data Retention > 200 Years

• Factory Programming (QTP) Available

• Pb-Free and RoHS Compliant

• 8-pin PDIP, SOIC, TSSOP, TDFN and MSOP

Packages

• Available for Extended Temperature Ranges:

Description:

The Microchip Technology Inc. 24AA014H/24LC014H

is a 1 Kbit Serial Electrically Erasable PROM with

operation down to 1.7V. The device is organized as a

single block of 128 x 8-bit memory with a 2-wire serial

interface. Low-current design permits operation with

maximum standby and active currents of only 1 μA and

400 μA, respectively. The device has a page write

capability for up to 16 bytes of data. Functional address

lines allow the connection of up to eight 24AA014H/

24LC014H devices on the same bus for up to 8 Kbits of

contiguous EEPROM memory. The device is available

in the standard 8-pin PDIP, 8-pin SOIC (150 mil),

TSSOP, 2x3 TDFN and MSOP packages.

Package Types

Block Diagram

Part

Number

VCC

Range

Max.

Clock

Temp.

Range

24AA014H 1.7V-5.5V 400 kHz

(1)

24LC014H 2.5V-5.5V 1 MHz I, E

Note 1: 100 kHz for V

CC < 1.8V

- Industrial (I): -40°C to +85°C

- Automotive (E): -40°C to +125°C

VCC

SCL

SDA

PDIP, MSOP

SOIC, TSSOP

SCL

SDA

TDFN

SCL

SDA

I/O

Control

Logic

Memory

Control

Logic

XDEC

HV Generator

EEPROM

Array

Write-Protect

Circuitry

YDEC

VSS

Sense Amp.

R/W Control

SDA

SCL

A0 A1 A2

1K I

™

Serial EEPROM with Half-Array Write-Protect

24AA014H/24LC014H

1.0 ELECTRICAL CHARACTERISTICS

Absolute Maximum Ratings

(†)

VCC.............................................................................................................................................................................6.5V

All inputs and outputs w.r.t. V

SS ......................................................................................................... -0.6V to VCC +1.0V

Storage temperature ...............................................................................................................................-65°C to +150°C

Ambient temperature with power applied................................................................................................-40°C to +125°C

ESD protection on all pins ......................................................................................................................................................≥ 4 kV

† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the

device. This is a stress rating only and functional operation of the device at those or any other conditions above those

indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for

extended periods may affect device reliability.

TABLE 1-1: DC CHARACTERISTICS

All parameters apply across the

specified operating ranges unless

otherwise noted.

Electrical Characteristics:

Industrial (I): VCC = +1.7V to 5.5V TA = -40°C to +85°C

Automotive (E): V

CC = +2.5V to 5.5V TA = -40°C to +125°C

Parameter Symbol Min. Max. Units Conditions

SCL and SDA pins:

High-level input voltage V

IH 0.7 VCC —V

Low-level input voltage VIL — 0.3 VCC V

Hysteresis of Schmitt Trigger inputs VHYS 0.05 VCC —V(Note 1)

Low-level output voltage V

OL —0.40VIOL = 3.0 mA, VCC = 4.5V

OL = 2.1 mA, VCC = 2.5V

Input leakage current ILI —±1μΑ VIN = VSS or VCC, WP = Vss

Output leakage current I

LO —±1μAVOUT = VSS or VCC

Pin capacitance (all inputs/outputs) CIN, COUT —10pFVCC = 5.0V (Note 1)

A = 25°C, f = 1 MHz

Operating current I

CC Read — 400 μAVCC = 5.5V, SCL = 400 kHz

ICC Write — 3 mA VCC = 5.5V

Standby current ICCS —1μAVCC = 5.5V, SDA = SCL = VCC

WP = V

SS, A0, A1, A2 = VSS

Note 1: This parameter is periodically sampled and not 100% tested.

24AA014H/24LC014H

TABLE 1-2: AC CHARACTERISTICS

AC CHARACTERISTICS

Electrical Characteristics:

Industrial (I): VCC = +1.7V to 5.5V TA = -40°C to +85°C

Automotive (E): V

CC = +2.5V to 5.5V TA = -40°C to +125°C

Param.

No.

Symbol Characteristic Min. Max. Units Conditions

CLK Clock frequency —

—

100

400

1000

kHz 1.7V ≤ VCC < 1.8V

1.8V ≤ V

CC ≤ 5.5V

2.5V ≤ V

CC ≤ 5.5V (24LC014H)

HIGH Clock high time 4000

600

500

—

ns 1.7V ≤ VCC < 1.8V

1.8V ≤ V

CC ≤ 5.5V

2.5V ≤ V

CC ≤ 5.5V (24LC014H)

LOW Clock low time 4700

1300

500

—

ns 1.7V ≤ VCC < 1.8V

1.8V ≤ V

CC ≤ 5.5V

2.5V ≤ V

CC ≤ 5.5V (24LC014H)

R SDA and SCL rise time (Note 1) —

—

1000

300

ns 1.7V ≤ VCC < 1.8V

1.8V ≤ V

CC ≤ 5.5V

2.5V ≤ V

CC ≤ 5.5V (24LC014H)

F SDA and SCL fall time (Note 1) —

—

1000

300

ns 1.7V ≤ VCC < 1.8V

1.8V ≤ V

CC ≤ 5.5V

2.5V ≤ V

CC ≤ 5.5V (24LC014H)

HD:STA Start condition hold time 4000

600

250

—

ns 1.7V ≤ VCC < 1.8V

1.8V ≤ V

CC ≤ 5.5V

2.5V ≤ V

CC ≤ 5.5V (24LC014H)

SU:STA Start condition setup time 4700

600

250

—

ns 1.7V ≤ VCC < 1.8V

1.8V ≤ V

CC ≤ 5.5V

2.5V ≤ V

CC ≤ 5.5V (24LC014H)

HD:DAT Data input hold time 0 — ns (Note 2)

SU:DAT Data input setup time 250

100

—

ns 1.7V ≤ VCC < 1.8V

1.8V ≤ V

CC ≤ 5.5V

2.5V ≤ V

CC ≤ 5.5V (24LC014H)

10 T

SU:STO Stop condition setup time 4000

600

250

—

ns 1.7V ≤ VCC < 1.8V

1.8V ≤ V

CC ≤ 5.5V

2.5V ≤ V

CC ≤ 5.5V (24LC014H)

11 T

SU:WP WP setup time 4000

600

—

ns 1.7V ≤ VCC < 1.8V

1.8V ≤ V

CC ≤ 5.5V

2.5V ≤ V

CC ≤ 5.5V (24LC014H)

12 T

HD:WP WP hold time 4700

600

—

ns 1.7V ≤ VCC < 1.8V

1.8V ≤ V

CC ≤ 5.5V

2.5V ≤ V

CC ≤ 5.5V (24LC014H)

13 T

AA Output valid from clock (Note 2) —

—

3500

900

400

ns 1.7V ≤ VCC < 1.8V

1.8V ≤ V

CC ≤ 5.5V

2.5V ≤ V

CC ≤ 5.5V (24LC014H)

14 T

BUF Bus free time: Time the bus must

be free before a new transmission

can start

1300

4700

—

ns 1.7V ≤ VCC < 1.8V

1.8V ≤ V

CC ≤ 5.5V

2.5V ≤ V

CC ≤ 5.5V (24LC014H)

16 T

SP Input filter spike suppression

(SDA and SCL pins)

— 50 ns 24AA014H

(Note 1 and Note 3)

17 T

WC Write cycle time (byte or page) — 5 ms —

18 — Endurance 1M — cycles 25°C, V

CC = 5.5V, Block mode

(Note 4)

Note 1: Not 100% tested. C

B = total capacitance of one bus line in pF.

2: As a transmitter, the device must provide an internal minimum delay time to bridge the undefined region (minimum

300 ns) of the falling edge of SCL to avoid unintended generation of Start or Stop conditions.

3: The combined T

SP and VHYS specifications are due to new Schmitt Trigger inputs, which provide improved noise spike

suppression. This eliminates the need for a T

I specification for standard operation.

4: This parameter is not tested but ensured by characterization. For endurance estimates in a specific application, please

consult the Total Endurance™ Model which can be obtained from Microchip’s web site at www.microchip.com.

P1-P3 P4-P6 P7-P9 P10-P12 P13-P15 P16-P18 P19-P21 P22-P24 P25-P27 P28-P28

24LC014H-E/MS

Mfr. #:

Buy 24LC014H-E/MS

Manufacturer:

Microchip Technology

Description:

EEPROM 1K 128 X 8 SERIAL EE 2.5V EXT 1/2 ARRAYWP

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

24LC014H-E/MS

24LC014H-E/MS

Products related to this Datasheet