OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

S2S5FA0F

P1-P3P4-P6P7-P9P10-P10
S2S5FA0F
4
Sheet No.: OP140
19EN
60
RMS on-state current I
T
(rms) (mA)
-
30
-
20
-
10
0
10
20
30
40
50
60
70
80
90
100
10
20
30
40
50
Forward current I
F
(mA)
-
30
-
20
-
10
0
10
20
30
40
50
60
70
80
90
100
10
20
30
40
50
60
70
0
Fig.1 Forward current vs. ambient temperature
Ambient temperature Ta (°C)
Fig.2 RMS on-state current vs. ambient temperature
Ambient temperature Ta (°C)
S2S5FA0F
5
Sheet No.: OP140
19EN
■
Supplement
● The business dealing name used for this product when ordered or delivered shall be S2S5FA0F.
● Refer to the attached sheet, page 7 to 9.
● Isolation voltage shall be measured in the following method.
(1) Short between pins 1 to 2 on the primary side and between pins 3 to 4 on the secondary side.
(2) The dielectric withstanding tester with zero-cross circuit shall be used.
(3) The wave form of applied voltage shall be a sine wave.
(It is recommended that the isolation voltage be measured in insulation oil.)
● This Model is approved by UL and CSA
Approved Model No. : S2S5
UL File No. : E64380
CSA File No. : CA95323
CSA approved mark " " shall be indicated on minimum unit package.
● This product is not designed against irradiation.
This product is assembled with electrical input and output.
This product incorporates non-coherent light emitting diode.
● ODS materials
(1) This product shall not contain the following materials.
(2) Also, the following materials shall not be used in the production process for this product.
Materials for ODS : CFC
S
, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methyl chloroform)
● Specified brominated flame retardants (PBB and PBDE) are not used in this device at all.
● Compliance with each regulation
(1) The RoHS directive(2002/95/EC)
(2) This product complies with the RoHS directive(2002/95/EC)
Object substances: mercury, lead (except for lead in high melting temperature type solders
*1
and
glass of electronic components), cadmium, hexavalent chromium, polybrominated biphenyls (PBB)
and polybrominated diphenyl ethers (PBDE)
● Content of six substances specified in Management Methods for Control of Pollution Caused by
Electronic Information Products Regulation (Chinese : 电子信息产品污染控制管理办法)
✓: indicates that the content of the toxic and hazardous substance in all the homogeneous materials
of the part is below the concentration limit requirement as described in SJ/T 11363-2006 standard .
Category
Toxic and hazardous substances
Lead
(Pb)
Mercury
(Hg)
Cadmium
(Cd)
Hexavalent
chromium
(Cr
6+
)
Polybrominated
biphenyls
(PBB)
Polybrominated
biphenyl ethers
(PBDE)
Phototriac coupler
✓ ✓ ✓ ✓ ✓ ✓
S2S5FA0F
6
Sheet No.: OP140
19EN
■
Notes
● Circuit design
(1) The LED used in the Phototriac coupler generally decreases the light emission power by operation.
In case of long operation time, please decide I
F
value as 2 times or more of the Maximum value
of the Minimum triggering current at circuit design with considering the decreases of the light
emission power of the LED. (50%/5years)
(2) Input current (I
F
) at off-state shall be set 0.1mA or less.
(3) In case that pulse drive is carried out, the pulse width of input signal should be 1ms or more.
● Usage
Only for triggering medium power triac and high power triac.
(This model shall be used under the condition on which power triac turns on.)
● Cleaning
(1) Solvent cleaning : Solvent temperature 45°C or less, Immersion for 3 min or less
(2) Ultrasonic cleaning : The effect to device by ultrasonic cleaning differs
by cleaning bath size, ultrasonic power
output, cleaning time, PCB size or device mounting condition etc.
Please test it in actual using condition
and confirm that doesn't occur any defect before starting the ultrasonic cleaning.
(3) Applicable solvents are as follows.
Applicable solvent : Ethyl alcohol, Methyl alcohol, Isopropyl alcohol
When the other solvent is used, there are cases that the packaging resin is eroded.
Please use the other solvent after thorough confirmation is performed in actual using condition.
● Precautions for Soldering Phototriac couplers
(1) In the case of flow soldering (Whole dipping is possible.)
It is recommended that flow soldering be carried out at 260°C or less
and within 10s (Pre-heating : 100 to 150°C, 30 to 80s).
(2 times or less)
(2) It is recommended to be done at the temperature and the time within the temperature profile as shown
in the figure below. (2 times or less)
(3) In the case of hand soldering
It is recommended that hand soldering be carried out at 400°C or less and within 3s : Within 2 times
(4) Other precautions
Depending on equipment and soldering conditions (temperature, Using solder etc.),
the effect to junction between PCB and lead pins of photocoupler is different.
Please confirm that there is no problem on the actual use conditions.
Pre-heat
150°C to 180°C, 120s or less
Reflow
220°C or more, 60s or less
Terminal : 260°C peak
(Package surface : 250°C peak)
1min
2min 3min 4min
100°C
200°C
300°C
P1-P3P4-P6P7-P9P10-P10

S2S5FA0F

Mfr. #:
Buy S2S5FA0F
Manufacturer:
Sharp Microelectronics
Description:
Triac & SCR Output Optocouplers Phototriac Coupler
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet